0
take the positive from speaker A and twist the copper wire together with the positive wire from speaker B. then take those two (positive) wires from A and B and put it in Channel 1 positive terminal. then take the negative from speaker A and twist the copper wire together with the negative wire from speaker B. take those two (negative) wires and put them in the negative terminal under channel 1. then do the same for your other 2 speakers, except in channel 2
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
When hooking up an amp and speakers do you wire the speakers through the stereo or the amp?
Hook your speakers up to the amp.
How do you hook up an vr3 200 watt 2 channel amp to a car stereo?
well you hook it up
Can you hook up one subwoofer to a 2 channel amp?
uhhh noo
How do you hook up speakers to microphones?
You have to employ the microphone jack on the amplifier providing the signal to the speakers. If you don't have a mic jack on your amp, your out of luck.
Can you hook up two 8 ohm svc subwoofers to a one channel amp?
If you connect two 8 ohm speakers to the average car amp, then yes, probably. Most car amps can handle a 4 ohm load, which is what it would be.
How many sub woofers can you hook up to a 4 channel amp?
Normally 1 or 2.
What does 2 channel compatible mean for use with one amp?
Easy Question--- One Channel is for the "High End" or Trebble-- The Other Channel is for the "Lower End" or Bass partition of the amplifier-- Careful not to hook up High End speakers to the "Bass Channel, as they will generally POP like the WEASEL!
I have a 2 channel nitro amp 2000watts amp and it always gets hot after 10min. it's been hooked it up to several cars and it's the only amp that gives trouble every other amp works fine?
If it's running so hot you can't touch it, in most cases it will be due to either the way the speakers are hooked up or the impedence of the speakers. You can incresse the resistance to the amp to have it run cooler by connecting speakers in series or getting speakers with a higher ohm rating. The lower the resistance (2 ohm, 4 ohm, 8 ohm) the more current flows though the amp making it hotter. Remember if you hook multiple speakers in parallel it will cut the resistance in half. So if you connect speakers that are 4 ohm to the same channel you are running at 2 ohm. Check your amp's ratings.
Can you hook up two subwoofers to one receiver?
yes, you can, either via a Y-cable to the sub output, or via a pre-amp, or hook them up parallel to a mono amp or if you have a 2 channel amp then just hook them up regurally but if you have a mono amp then...have two positive and two negative wires coming out of the amp then hook 1 negative wire up to the negative spot on a speaker..then do the same with the other..then do the same with the positive
How would you hook up 2 8 ohm woofers with a 4 ohm dual voice coil woofer?
You could with a 4 channel amp. Bridge it to two channels and hook up the two 8 ohm woofers in parallel on the one bridged channel. Then hook the two coils on the dual coil woofer in series with the other bridged channel on the amp.
Can you hook up two subs to a mono channel amp?
yes all u have to do is bridge them together
Can you hook 2 subs to a mono amp?
Sure i have 2 400 watt rockfords connected to a 400watt kenwood mono amp. This statement made by another is true.You can hook up 20 subs to a mono amp; BUT you have to configure the speakers by impedance/ohms. if you hook two 2 ohm speakers to a 4 ohm steady amp in parallel you will soon buy a new amp. if you hook 10 speakers in series you will not even get it warm. Each speaker will also divide the available wattage and will not have a lot of power. Take it to a good shop if you don't know the formula for this. you may save your amp. BMyers Lake city, FL
