0
Usually not. The LED lights are soldered in series with each other, and it will be a very time consuming to attempt removing/replacing the offending led bulb and re-soldering them again. Chances are very high that some other component of this module will get damaged in the process. It will be far cheaper, in the long run, just to replace this high mount module.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do change the third brake light on c5 corvette?
You can't. The C5 third brake light is an LED unit. If the unit has went out the entire unit needs to be replaced. There are two bolts that hold the unit in that are accessed by removing the rear plate holder.
How do you replace third brake light bulb on 2002 Mercury Sable?
Its a whole led unit replace whole deal not bulb
How do you replace the third brake light on a 2001 GMC Yukon?
01 Yukon 3rd brake light removal......changing the third brake light on a 2001 Yukon is a relatively easy task. First open the rear liftgate (not just the glass). This will expose the two screws that secure the housing of the lamp to the body (it also exposes the connector plug which, obviously, you should unplug). After removing the two screws, separate the rubber housing from the LED lamp itself....and there you have it!...because the third brake light is a sealed lamp the entire brake light must be changed. you can�t just replace the bulbs. ...
What is the correct way to replace the third brake light in a 2004 Saturn L300?
Easy! Just goto the 3rd brake light and carefully pull off the cover... CAREFULL not to brake the snaps... before hand though, you have to go to the dealer to get the LED's, see how many you will need.
Why does your left LED brake light not work at all and your right LED brake light work when taillights are on?
you need to repair the lights and they will both work and your taillights will work properly
What is a Zafira Led brake light?
Zafira LED brake lights are brake lights that utilize LED lighting instead of regular bulbs. The information for this product says they are easy to install and the wire needed for the LED lamp is included. The price for a set of two is $160 to $165.
Do rear brake led lights on 2002 Chevy blazer burn out?
The center high mount led brake light unit has been known to go bad.
Your Peugeot 106 brake lights are not working.The Bulbs and fuse are ok and the brake light switch and the Back door brake LED work.?
the brake light fuse on a peugeot partner is F1O!! STOP SWITCH FUSE!!
How do you turn off your LED brake light that keeps blinking in your 1994 Oldsmobile 88 Royale?
check brake fluid level.
How do you replace third rear led brake light 2006 civic?
2006 Honda Civic center high mount stop (third 3rd brake light) light bulb lamp replacement procedure: Purchase the correct replacement center high mount stop (third 3rd brake light) bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information and full light bulb part numbers list. Then consult your owner's manual for the center high mount stop (third 3rd brake light) bulb replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. If there are multiple bulbs, you may want to consider replacing all at the same time in order to keep brightness and color equal (optional).
What would cause the third brake light on a 2003 Chevy Tahoe not to work when all other lights work and how would you replace?
I have same year Tahoe and same problem. Check fuses first to make sure it isn't a fuse. The third brake light assembly can be removed by opening the back door and unscrewing the screws. Then unplug the connector. A new unit is about $175.00 and the whole unit must be replacee as it is LED light not bulbs.
Why is there a warning light flashing when you push on the brake pedal its a orange light and looks like a oil filter with five lines on the inside of it?
If you have led lights when the brake light warning switch is closed (foot on brake) because it has a predetermined voltage and the rig is change to led's there is a different voltage used, hence an error warning light. can get around it by adding the original lamp in series with the brake circuit out of the way somewhere say under the dash.
