0
Cant get bolts off on battery wires going to starter 1998chevyblazer?
Wiki User
∙ 18y ago
you have to hold the battery cable or the nut behind it to keep it from turning with the nut you are removing.
Wiki User
∙ 18y ago
Add your answer:
Earn +20 pts
How do you replace the starter on a 1999 Buick Century?
first disconnect the battery. remove the bolts that support the starter. you may have to wiggle the starter out after you disconnect all of the wires going to the starter
How do you install a boat starter on and evinrude outboard motor?
Disconnect the battery. Disconnect the wires going to the starter, and remove the 3 bolts holding it in. Installation is the opposite. Follow the red battery cable if you can't find the starter.
How do you remove starter in 1991 Chevrolet caprice classic?
Disconnect the battery, locate the starter.. remove the mounting bolts, bring the starter down to where you can reach all of the wires going to the solenoid, and disconnect those.
What would cause a power wire to burn from the starter to the battery?
why would my starter wire burn, going from starter to battery
Is there a fuse in the battery cable going to the starter?
No
Where is the starter of a 1990 F-350 cargo van and how do you replace it?
The starter is located on the lower right hand side of the engine, and it will be bolted to the bellhousing of the transmission with two 1/2" or 13MM bolts. If it has only one wire going to it, you won't have to dis-connect the battery. The easiest way to tell this without crawling under, is if you know what the solenoid looks like that would be attached to the radiator support, behind the battery. If it doesn't, or the starter has more than one wire going to it, then the battery will have to be dis-connected. Remove the two bolts, and if the starter has one wire, a 3/8" or 10MM wrench will remove the bolt for the wire terminal. -Remove the wire first. Then the bolts for the starter, and pull it out, and drop it down.
How do i replace a Vectra 17td starter motor 17td 1998?
very simple to replace the starter on this engine, first disconnect the battery then after jacking the car up (easier from underneath ) locate the startermotor it is just under the manifold bolted to the gearbox it is around the size of a coke can. unbolt the three bolts and disconnect the two wires going to the starter the bigger one being the live feed from the battery replace starter with new one three bolts back in ,wires connected, battery back on job done good luck
Starter sounds like it is going out but was only replaced 4months agostarter battery tested good any idea?
Are the starter bolts tight ? It may have worn fly-wheel teeth. If you have the ticket on the new starter then I would take it back and get another 1.
Where is the starter on a 1994 Ford F150 5 liter and how do you replace it?
Starter is on the passenger side, bottom of engine going in to bell housing. Remove battery cables(ground side first) 3 bolts hold starter on. 2 wires attached to the end of the starter. reinstall in reverse.
How do you change the starter relay on a 1999 ford windstar?
The relay is located in the 12 volt ignition wiring harness going to the starter. The small wire on the starter is the ignition switch. The relay is located in the wiring harness. Are you sure the starter solnoide is not bad? When the ignition key is turned to the start location, you should read 14.1 volts going to the starter. If you read 14.1 volts, and the starter does not turn over. Check battery, and cables. Ok, Then replacement of starter is necessary. Starter bolts are 13mm. Brakeline bracket bolt is 15mm. Solnoide bolts are 13mm. Should take no more than 20 minutes to remove starter.Follow the + battery cable either mounted on the inner fender or on top of the starter
Can you short out a battery by replacing a starter?
yes if you dont remove the positive terminal off the battery before unistalling the starter or installing it the lead going to the starter will be hot.
How do you change a starter on a 1993 Buick century V6?
replacing the starter is relatively simple, what do is remove the wires from the starter solenoid which is located on top of the starter motor, and mark where the wires came from, there is a small terminal then there is a bigger terminal. oh and un hook the battery before that because it's an unpleastant surprise. then using a jack support the starter before the bolts are removed, then remove the bolts, which in most cases are 15mm, then lower the jack with the starter and put the new one one the jack. raise the jack and hook everything back up. get the starter secured and hook the wires up then the battery and turn it over. jeremy aka ccz5105
