Diagram Disassemble Crank Sensor 91 Pontiac Bonneville?
Did John Brennen convert to Islam
2 people found this useful
If it's the same as a 1999 model, the outside temperature module is located in front of the radiator and behind the front bumper.
first u take it out thyen take off the plastic un bolt every thing take off wire clips and its easier to just go get one from the junk yard u poo head
Answer It is on top of the PCV valve on the front of the engine by the alternator. (normally aspirated, non supercharged models only). The location depends on whether you have a normally aspirated 3800 V-6 (as in the SSE model) or the supercharged 3800 V-6. On the supercharged model (SSEi) there …are 2 map sensors mounted on a bracket above the rear valve cover, connected to the vacuum hosing. Each sensor is held on the bracket with 2 screws. One sensor runs the supercharger boost gauge, the other is used for engine management. The electrical connectors are identical, and it doesn't matter which sensor they are attached to, other than the fact you don't want to attach them in such a way as to tension the wires and cause damage to the wiring harness or connectors. There is a lot of emissions wiring and hoses that can interfere with getting to the sensors, along with spark wires, etc, so they are not easy to see in poor lighting. They connect to the vacuum hoses underneath, so carefully remove them, as on a car this old, the rubber connector and stiff vacuum piping can be brittle from engine compartment heat, and tear or break very easily. Any vacuum leaks can cause high engine idle speeds along with other driveability problems. ( Full Answer )
Answer . \ntry going to local parts store and buying a maintenance book .Such as haynes or chiltons ,they usually have that kind of diagrams in them.They usually cost 10-15 dollars and are very helpful on repairing your car.
Answer . \nCPS is located next to the flywheel left(passenger) side looking from the from front.
Hi! First you need to get a harmonic balancer puller. This pulley is located on the bottom of engine. Remove the tire and plastic so you can see it. Get a socket that fits the bolt I would recommend using a impact gun to get the bolt out. After its out pull the pulley and the sensor is located beh…ind it . Two bolts hold the bugger on , but it's set on a dowel so you may have to fiddle with it to get it off. Hope this helps! Jim ( Full Answer )
Answer . \nTry looking at the back of the engine on the maifold just before it connects to the exhaust pipe.
i have been told that it is located on the drivebelt end of the intake manifold on 3.0 and 3.8 liter motors. and on 3800 motors its on the the opposite end of the intake( drivers side rear of motor, mounted on rear of intake manifold.) im changeing mine tomm so I'll write back with info on how it go…es ( Full Answer )
there is a vacuum diagram under the hood of the car located near the hood latch. if it has been removed or faded one can be obtained from the repair manual chilton #28200. the book is a valuable source of information and a great investment.
I'm not a mechanic, but i changed my tps in a 92 bonney. it is located to the right of the supercarger. it is very visible because iy is toward the top of the engine. i had to use a special ratchet screwdriver(you can find one at autozone or a SEARS store).when you find it you have to adjust it to a… certain angle or your car wont shift like normal, it will shift very quick when you are driving, to the point where you have to drive it manually,so adjusting it correctly is kinda crucial. the tps itself can be seen-its got 3 wires coming out the end and is close to the throttle body. that's about the most info ican give. Like i said I'm no mechanic so i hope i gave you enough info to start you out. ( Full Answer )
Answer . \nPrice this part out at any GM dealer and ask them to print out a picture of the part which will show you the location of it on your engine. This is a free service. Mark
Answer . \nWhat model is your vehicle? I have a repair manual for mine, it's a 1990 Lumina Euro, but the boks covers other models. I can check it and see where it is located, but it may not be the same as yours. Only if the engine is the same I'm guessing. I'll check my book tomorrow (05/19/…06) and let you know what I find. ( Full Answer )
1995 Pontiac Bonneville it will die going down the road and start right back but jerks you have replaced mass air sensor fuel pump fuel filter crank sensor and injectors cleaned Any ideas?
Answer . \nThis has happened on my 97 twice- it was the fuel pressure regulator.
If you have a 2.2 engine ( 4 cyl. ) it is located under the ignition module at the back of the engine . Follow the plug wires to the coils, under the coils is the module under that is the crank sensor.
my son just replaced one on my car i also have a 1992 Bonneville it is located on the passenger side frount behind the tire you will need to remove your tire
Answer . Oxygen sensors are typically on the exhaust manifold, near the headpipe. They screw in and there is usually at least one way to reach them that doesn't involve pulling the engine. V6 engines typically have an O2 sensor for each side, and some vehicles have both front and rear oxygen sen…sors, which can total as many as 4 sensors. But typically the rear sensors don't fail as often as the fronts.\n. \nI don't know of any CO2 sensors in vehciles, just O2, so if you're looking for other information you'll need to get an answer from someone else. ( Full Answer )
A person can find a wiring diagram for a 1997 Pontiac Bonneville atmost GM dealerships. The dealerships are happy to help customerswith any requests.
I have a 94 it is located rigt above the thermostat it has a plug in it with 3 wires coming from it it is not to big you would need a phillip that looks sorta like a z it has two screws in it. it is above to the right of the thermostat. I just replaced mine.. Schelithea "Chics Rule". I have a 94 i…t is located rigt above the thermostat it has a plug in it with 3 wires coming from it it is not to big you would need a phillip that looks sorta like a z it has two screws in it. it is above to the right of the thermostat. I just replaced mine.. Schelithea "Chics Rule" ( Full Answer )
Answer you will have to hook up a scan tool to see if you have cranking rpm with motor spinning over. rpm singal. also when you crank the engine the check engine light will go out if it is working
Answer . \nThere is a snap ring that fits onto the handle itself. A flat screw driver, steel ruler or similar "tool" slid between the handle and door liner will allow you to release the snap ring from the shaft that holds it onto the handle. Looking at the handle with the knob to the right, the… ring slides off to the left. Chilton book #28320 Page 10-13 Fig. 43 gives a good picture. Hope this helps.\nLangalier@hotmail.com. ( Full Answer )
Answer . \nYes, it is possible. If you have checked all fuses in the dash and they are ok, try looking for a fuse panel under the hood in the engine compartment. There's been known to be ignition fuses in those panels in the engine compartment (if it is equipped with the engine compartment fuse …panel). Otherwise, check starter relay, ignition wires near starter relay, ground wires, or even the ignition cylinder (where the ignition key goes), it may not be getting a good connection and could be wore out. ( Full Answer )
Answer-no crank . 1)bad or discharged battery -charge(12.6volts,perform draw test) or replace. 2)corroded battery terminals and posts -clean. 3)corroded battery cables -replace. 4)bad starter and/or starter relay. 5)bad ignition switch. 6)bad connection to starter. 7)melted fusible link(s). 8)bro…ken starter signal wire. 9)alarm system has disabled starting. 10)bad transmission neutral safety switch or inhibitor switch. 11)make sure it is in "Park" 12)make sure engine isn't locked up. 13)make sure A/C compressor and other accessories are not locked up. 14)bad coded ignition key(resistor in key). ( Full Answer )
Answer . \ncrawl under the car to the back side of the engine remove the 2 bolts pull sensor out and replace with new 1 in reverse of removal order.caution do not turn engine over while sensor is not installed.
Answer . The MAF sensor is always located in the air duct between the air filter and the throttle body. I'm a retired ASE Master/L-1 Technician. I still keep current with the latest automotive technology. Visit my blog for cool articles and TSB's: http://free-auto-repair-advice.blogsp…ot.com ( Full Answer )
This is a vertical unit directly behind the water pump on the passenger side of the motor.
Answer . Oxygen sensors are located in the exhaust manifolds & in the exhaust pipes on most vehicles
The Map Sensor on that model is located on the passengers side of the motor. It is on top of the plastic intake plenum and has a plug in connector. It is labeled "Sensor Pressure and has a part number of 09359409". BE CAREFUL REMOVING IT. It has a rubber gasket so wiggle it out. I have broken a few …trying to remove them. It is held in place with a plastic clip connector. ( Full Answer )
1996 Pontiac Bonneville sse and it keeps stalling out in me . Cannot go far and it stops please help i heard it was a crank sensor not sure?
Excessive stalling is often a problem with your idle air control valve (IAC). Before buying a new one, try removing and carefully cleaning yours with carbureator cleaner. Do not change the setting by turning the screw in valve, just clean it. It would also be benificial to see if the computer is sto…ring any trouble codes, most auto part stores will do this for free now. ( Full Answer )
On the intake manifold near the thermostat housing. It will be two wires a yellow and one black wire.
The crankshaft sensor is on the side of the engine behind thealternator. It is mounted close to the oil filter,
Typically the O2 sensor is located at the back of the engine, follow the exhaust manifold and it should be attached somewhere near it
There is a crankshaft position sensor. It is located Under the hood, center, lower engine area, front side of engine, passenger side of crankshaft pulley, mounted in engine block
bad idle and chec engine light comes on. this can be checked with and obd 1 code reader
evidentually it is a big secret. They will only tell you where to go to buy one.
I think, and I THINK it is under the plastic cover on the left side of the engine, at least it is with a 2.0 4 cylender motor. You have to remove the belt covor than the belt, than the sensor should be visible. I say this because i read it in a Pontiac manual, that plus there are wires running in to… the covor. Hope it helps ( Full Answer )
Where is the crank shaft located on a 1999 Pontiac Bonneville? I have bought the part. Just can't find where it goes.
The Crankshaft Position sensor is mounted on the bottom right side of the crankshaft pulley, mounted on the timing chain cover. Only 2 bolts hold it in place and has a 4 wire connector plugged into the sensor. Hope this helps
They sell them on Ebay. I have not bought one Also the have some posted on HardCore Pontiac's but it is of a 66. I need one for the 67 also. A question that I have is do you know where the black wire with a white stripe runs to on you alternator harness? I need to know exactly where that one goes. M…y email is firstname.lastname@example.org thank you. ( Full Answer )
There are two oxygen sensors, there is one located in the exhaust system before the catalytic converter and one after the catalytic converter.
behind the motor about dead center usually a white cylindrical plug almost. it will be right behind the plastic cover
unclip the old one, unscrew it. then screw in the new one and clip the new one on
The crankshaft position sensor is located behind the harmonic balancer. You will need a harmonic balancer puller and an impact wrench good for at least 750 ft pounds. Access the harmonic balancer through the passenger side wheel well. Remove the harmonic balancer center bolt and use the puller to re…move the balancer. Use 1/4 - 28 X 3 inch bolts on the puller. The sensor is held with two screws. Be careful not to damage the weatherpack connector when releasing it from the sensor. ( Full Answer )
The sensor is located on the right side of the the crankshaft attached by 2 bolts thru the timing cover it will be hard to see due to the pulley.
I am serious on this answer, go to Autozone.com, sign up to become a member for the vehicle repair guides and when you enter the part you are searching, over to the right of the screen there will be a place to click on that says "vehicle repair guides", "locate the part on my vehicle" It will tell y…ou exactly where the part is at on your make and model, and it will also tell you how to test the part, removal and replacement and also visual diagrams to help you along! I know this because i use it all the time for my car! Me being a self-reliant female makes it much easier to find and fix the problem myself! If i can, You can!!!! ( Full Answer )
Shouldn't need them just look inside the trunk and undo the plastic nobs behind trunk trim panel.
It depends what engine you have but its typically on the front of the engine(th side where the belts are) and its on the front timing cover, sometimes under the crankshaft pulley,
It is under the harmonic balancer, the large pulley on the end of the crank shaft. To remove, jack up the right front of the car. Remove the tire. Remove the plastic splash shield. Remove the serpentine belt before you jack the car. Use an air impact wrench to remove the large bolt in the end of the… crank. Use a puller to remove the balancer. DO NOT try to pry the balancer off. Metal fins on the back side and you will destroy them. The crank sensor is now visible and can be easily removed. Mark the old sensor's position and install the new one in the exact same position. It has room for adjustment. It has to line up perfectly with the metal fins on the back side of the balancer. If you don't have an air impact wrench, better borrow one. No good way to keep the engine from turning using a socket and pull bar. ( Full Answer )
I have a 92 Buick Riviera 3800. The temp sensor on my car is just underneath the throttle body... driver's side of the engine
You got to have a star bit with a hole in the middle the mad is on top of the air duct
First locate map sensor,on top of throttle body it's held on by two star bit set screws. After removing and then unplugging make sure surface is clean and add a little electrical contact lube. Install