Does a 1994 Buick Skylark have a throttle position sensor or a crank sensor?

Have someone press the throttle from inside and watch to see what moves. The cable is connected to a shaft that goes through the throttle body. The TPS is connected to that shaft.

you have to adjust the tps by loosing the screws and rotating it till it reads 0.50 volts [you need a scanner to do it]

I just purchased the throttle sensor for a 2003 Buick rendezvous and was wondering if anyone could tell me where it located and how easy is it to put in.

How to install tps

throttle position sensor believe it or not!

let a shop do it be cause it will has to be udjusted it will run about 60 dollars

I took it to a shop. It was the crankshaft position sensor.

On the trans.

While it could be an ignition problem, the most likely cuplrits are the fuel pump or the Throttle position sensor. Good Luck While it could be an ignition problem, the most likely cuplrits are the fuel pump or the Throttle position sensor. Good Luck

It will physically bolt in--HOWEVER--the 3.8 uses a separate cam position sensor while the 3.3 incorporates it into a single sensor unit with the crank position sensor, so the wiring harness is different. Also--the computer calibration is different owing to the difference in displacement. Unless a donor car is available with the correct wiring and ECM/ECU and one has the knowledge to do this--it is NOT recommended.

Somewhere on the exhaust system. LOOK

"http://wiki.answers.com/Q/Where_is_the_crank_sensor_on_a_1990_2.5_buick_skylark"

will the fenders from a 1971 Buick Skylark Custom fit a 1972 Buick Skylark?

The crankshaft position sensor on a Buick is located behind th Harmic balancer. It should have a wire plugged in to it.

throttle positioning sensor

how to remove crankshaft position sensor from 91 Buick Regal

Buick Skylark was created in 1953.

The camshaft position sensor on a 1992 Buick Regal looks like the end of a ratchet.

It is mounted on the throttle shaft usually on the other side from the throttle cables. It has a three wire connector plugged into it.

The crankshaft position sensor, on your 1992 Buick regal 3.1 liter, is located on the back of the engine. The crankshaft position sensor is on the inside of the engine cover.

the oxygen sensor is located in/on the exhaust manifold.it looks like a spark plug with a wire coming out of the top

even if its got bad wires or plugs it would run but run ruff or with a miss!!!! so check-- crank sensor, ignition module, ignition coil, or throttle position sensor..

REar side of radiator approx. 1/3 from the top

It's on the driver's side of the rear cylinder head.

If its in the same location as my 96 Bonneville, It would be on the throttle body :) Almost Right below the ECM and above you're Thermostat, If you now how to rev you're car from under the hood by pulling the cable, its connected to that. :)

The temperature sensor to the computer is located on the thermostat housing. On the 4 cylinder it is on the right side of the engine block.

hw much does an 81 buick skylark weigh?

yes it will, i have a 1971 skylark with a 72' fender on it.

try checking the throttle position sensor.

picture diagrams of engine for 1997 buick skylark

where is the blower motor resistor located on 97 buick skylark

If you mean the engine, yes. The actual car, no.

Have the codes read, my problem was with the throttle position sensor. My 94 le Sabre was also stalling occasionally.

It sounds like the Throttle Position Sensor needs replaced.

Not positive, but there is something attached to the bottom of the coolant tank, maybe that's it.

floorboard inside car always wet 1995 buick skylark

How do u set the timing on a 1972 buick skylark

behind the crank pulley

The crankshaft position sensor is mounted on the front of the engine. It bolts on, and has one wiring plug.

you will need a set of torqs bits they kinda look like Allen wrenches but there star shaped & it should only have 1 clip on it with about 2 to 4 wires on it

I'd suspect a loose, damaged or unhooked vacuum hose/line around the upper/lower intake. Or a faulty throttle position sensor.

directly on top of the throttle body intake

I had the same problem with my 90 buick century, Replacing the temperature sensor did the trick, it is located above and behind the water pump.

It is located above oil filter, If your lucky you will be able to pull straight out after (after removing 1 small bolt)dropping starter down, however their usually rusted and strongly magnetized and will break then your if for a world of fun.

a 1991 buick skylark has 4" speakers in the dash and 6x9's in back

Where is the transmission solenoid located on a 1995 buick skylark custom?

Could be cam sensor, crank sensor, throttle position sensor, mass airflow sensor or the magnet on the crank. We just replaced all of the above and found out the hard way it was the last...and cheapest. Pull the cam sensor, look at the end of your cam and see if the magnet is damaged.

The mass air flow sensor is located in the throttle body housing on the 3800 engine. There should be 4 screws that hold it down to the housing. Once they screws are removed, the sensor lifts off of the throttle body.

how do you replace the alternator in a 97buick skylark

Remove the air cleaner and the air supply from the top of the throttle body. Have someone step inside the vehicle and slowly press and release the throttle while the engine is off. Watch to see what moves. The throttle butterfly is operated by the cable from the accelerator pedal. Notice that the cable goes over a sprocket that moves the throttle. On the OPPOSITE side of the throttle body should be a black plastic…