Head Gaskets and Valve Covers
Saturn (car)
Toyota Tacoma
Grand Am SE

Does anybody know the torque specs for the cylinder head on a 1997 Saturn 1 9 DOHC and the torque specs for the intake?

222324

Top Answer
User Avatar
Wiki User
2006-02-20 03:46:25
2006-02-20 03:46:25

Cylinder head bolt tightening sequence Intake side of engine (Rear) left to right (pass to driver) 8 4 1 5 9 Intake side (frount) left to right 7 3 2 6 10 This is the cylinder head bolt tightening sequence for a 1.9 DOHC engine. Torque as follows: Step 1-First torque=48 ftlbs Step 2-Remove bolts (using the opposite of the tightening sequence) Coat the threads with engine oil reinstall bolts. In sequence tighten first to 22 ftlbs, then to 37 ftlbs. Step 3-Finally tighten all bolts an additional 1/4 turn. Torque Specs for intake: 22ftlbs. The bolts in the rear of the engine (passenger to driverside) are 8 4 1 5 9 In the frount of the engine it is 7 3 2 6 10. It should be a clockwise spiral.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

what the torque spec for the cylinder head on a 2003 saturn L300

User Avatar

What are the torque specifications and the tightening sequence of the cylinder head bolts on a 1996 Saturn SL1?

User Avatar

The 1999 Pontiac cylinder head gasket bolt torque specification is 160 pounds. The intake manifold bolt torque specification is 90 pounds.

User Avatar

For the 1996 Saturn SL1 1.9 liter 4-cylinder, the torque in sequence one is 22 ft/lbs. In step two, torque in sequence to 37 ft/lbs. In step three, turn all the bolts 90 degrees and double check the final torque in the sequence.

User Avatar

Get a manual on your car and it will give you the settings of the intake, exhaust bolts plus the head bolts and torque pattern.

User Avatar

torque specs are lower intake 115in-ibs upper intake 18ft-lbs

User Avatar

What is the torque spec for a 2001 Saturn head? It has only a single cam

User Avatar

intake torque specs 2002 buik century

User Avatar

There are dozens of torque specifications, for the 2002 Saturn. A complete list of torque specifications, can be obtained from most General Motors dealerships

User Avatar

how to torque an aluminum intake for 350 25 ft./lbs.

User Avatar

What are the intake manifold torque specs on 1998 Oldsmobile bravada?"

User Avatar

What is the cylinder head torque setting on a Isuzu npr

User Avatar

Remove the intake and exhaust manifolds. Remove the head. Torque the head and manifolds to the correct torque and sequence, you will need a repair manual for this.

User Avatar

The lower intake manifold to cylinder head torque specification is 132 inch pounds. The upper plastic intake plenum to lower intake should be done in three steps 22 inch pounds, 44 inch pounds and thirdly 89 inch pounds. Be sure to follow the appropriate tightening sequence diagram.

User Avatar

If your 1988 Celebrity has the 2.5L 4 cylinder engine the torque is 25 ft lbs. If you have the 2.8L V6 engine the torque is 23 ft lbs. This per my 1988 factory service manual.

User Avatar

22ft pounds is the torque spec, The tightning sequence is as follows. Upper side: 8-4-1-5 Lower side: 7-3-2-6-9

User Avatar

what are the torque specifications for 2002 ford 4.0 intake manifold

User Avatar

torque for 2c engine cylinder head bolts

User Avatar

Ford CFord Cylinder Head Torque Specificationsylinder Head Torque Specifications

User Avatar

what torque specs on cam shaft bolts 2000 saturn 2.2


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.