0
Does the bolt on the crankshaft pulley go to the left or right to tighten?
BenVrgas
Turn it to the RIGHT.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you remove crankshaft pulley bolt from a Nissan Pathfinder is it right or left hand thread?
1998 Nissan pathfinder crankshaft pulley bolt is right handed.
My bolt on the crankshaft pulley wont tighten on My 88 B2200 I think the threads a stripped on it will I need to buy an new crankshaft?
Usually the crankshaft is made of harder metal than the bolt, so you should be able to just replace the bolt. But who knows for certain until you try.
How do you easily remove the crankshaft pulley on a 1989 suzuki samurai?
The crankshaft has four 8mm bolts that hold the pulley onto the camdrive pulley.Do not remove the large bolt in the center unless you are going to replace the crankshaft seal.Also be sure to tighten that bolt if removed, it will walk back and forth and damage the crank eventually.
Mitsubishi gto crankshaft pulley is the bolt right or left hand thread?
Right hand thread
Is the crankshaft pulley bolt left hand or right hand thread?
Right hand thread
Where is the crankshaft bolt on 1996 ford winstar 3.8?
In middle of crankshaft pulley
How do you remove a crankshaft pulley on a 67 Chevelle?
The crankshaft pulley unbolts from the harmonic balancer. The harmonic balancer can be removed from the crankshaft with a 3 bolt puller.
What is crankshaft pulley bolt size 96 ford range?
22mm bolt
How do you take a crankshaft pulley off of a 1996 mercury mystique?
Jack the motor up and take the motor mount loose on the top right side. Carefully lower the motor down until you see the crankshaft bolt on the bottom. Then take the center bolt off the crankshaft and then the pulley will come off.
Which direction does a crankshaft pulley bolt come of on a 95 Honda accord?
crankshaft pulley bolt is left hand thread,so it will come out opposite direction to normal bolts
How do you remove 1997 Avalon crank shaft pulley?
remove 22mm center bolt its regular thread there are 2 threaded holes in pulley you will need the right pulley remover with the right bolts for the pulley you can get this at most parts stores make sure to not mess up crankshaft bolt threads
How do you change the serpentine belt on a 1997 Chrysler Sebring?
for 2.5 v6on the 1997 2.5L V6 models there is a tensioner pully that is held on w/a bolt on the front of the pulley and adjusted with a bolt on the mount that is to the left of the pulley. be sure you don't have the spring loaded autotensioner because some models on the 1997 line had them. first you have to loosen the bolt holding the tensioner on. then the other bolt on the side of the pulley has to be loosened to relieve the tension on the belt. then just take the belt off and replace with a new one with it going on the right side of the alternator and the compressor pulleys the left side of of the tensioner pulley motor crankshaft pulley. when you start to tighten the belt you have to tighten the bolt that holds the pulley on till it holds it straight but not tight. then you tighten the adjuster bolt until the belt only flexes less than an inch in the area between the alternator and the crankshaft pulley. tighten the hold down bolt and start. listen for slippage when your transmission shifts when you are dogging the car out. if you hear a loud squealch when it shifts then the belt isn't tight enough. on the 2.5L v6 model there is also a v-belt for the power steering pump which requires the removal of the serpentine belt for replacement.
