0
What else can I help you with?
How do you do a throttle body relearn on a 2005 sentra?
Warm up engine. - Put in neutral (n)! -Make sure everything is off (RADIO, AC, ETC.) -Turn ignition switch ?OFF? and wait at least 10 seconds. -Confirm that accelerator pedal is fully released, turn ignition switch ?ON? and wait 3 seconds. -Repeat the following procedure quickly five times within 5 seconds. a. Fully depress the accelerator pedal. b. Fully release the accelerator pedal. -Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the MIL stops blinking and turned ON. -Fully release the accelerator pedal within 3 seconds after the MIL goes ON. -Start engine and let it idle. -Wait 20 seconds.
If someone installed a 1999 Civic engine and standard transmission into a 1996 Accura and you have a 1.8 Accura automatic flywheel how can you tell if the transmission came from a Honda or an Accura?
Acura makes Honda. Honda makes Acura
How do you reset the change engine oil light on your 2000 Silverado?
Turn the ignition key to the run position and pump the accelerator 3 times within 5 seconds.
Your speedometer went down to 0 whilst the car was still moving so you pressed on the accelerator a bit more and it went back to 60MPH after about 2 seconds Would this be a problem with your engine?
This is a problem with the speedometer, not with the engine.
You changed the trotle body on your sentra but now the rpm is too hi?
Look up "Idle Re-Learn" for Nissan Sentra. There is a process where the throttle body/Idle Sensor must be re-set. This can be done at the dealer or through a series of steps. Idle Relearn BASIC SERVICE PROCEDURE - Turn ignition switch OFF and wait at least 10 seconds. - Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds. - Repeat the following procedure quickly five times within 5 seconds. a. Fully depress the accelerator pedal. b. Fully release the accelerator pedal. - Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the MIL stops blinking and turned ON. - Fully release the accelerator pedal within 3 seconds after the MIL goes off. - Start engine and let it idle. - Wait 20 seconds. - Rev up the engine two or three times and make sure that idle speed and ignition timing are within the specifications.
Warm engine won't start?
why won't 1992 Accura Integra RS start in warm weather
Does the 2003 Accura TL have a timing belt or chain?
Your 3.2 liter V6 engine has a timing BELT
How to reset an oil change light on a Jeep Patriot 2012?
1. Turn the ignition switch to the ON position. Do notstart the engine.2. Fully depress the accelerator pedal, slowly, three timeswithin 10 seconds.3. Turn the ignition switch to the OFF/LOCK position.1. Turn the ignition switch to the ON position. Do notstart the engine.2. Fully depress the accelerator pedal, slowly, three timeswithin 10 seconds.3. Turn the ignition switch to the OFF/LOCK position.
How do you reset the ecu on a 92 300zx?
1 Put the key in the ignition and turn it to the "On" position, but don't start the engine.2 Press down on the accelerator very fast five times within five seconds. You have to press the pedal all the way to the floor each time. Wait 10 seconds.3Press the accelerator to the floor and hold it for 10 seconds, or until the "Check Engine" light turns on and off. Repeat this step again.4Turn off the ignition and wait about three minutes. Start the engine and examine the instrument panel. The Check Engine light should now be off and the ECU reset
No acceleration while pressing down on accelerator?
If the engine is revving up, then the transmission is having problems. If the engine is not revving, then check the linkage from the accelerator to the throttle body.
2002 Chevy Monte Carlo change engine oil light wont reset I have tried the method suggested which was turn key on pat the accelerator 3 times within 5 seconds then turn key off then start engine?
turn key on pump accelerator 3 times hold on 3rd time till light changes
How do you reset computer on your titan?
AnswerI have a Titan and you cannot reset the computer by diconnecting the battery. It must be taken to the Nissan dealer and have it cleared.*edit:ECU ResettingTiming is extremely critical. If it is NOT DONE within the specifird time, the ECU will not reset and the Check Engine Light (CEL) will continue to remain ON. A stop watch or an analog clock with a second hand will be useful.Operations Procedures:1. Confirm that accelerator pedal is fully released, turn ignition switch "ON" and wait 3 seconds.2. Repeat the following steps (2a and 2b) procedures quickly five times within 5 seconds.2a. Fully depress the accelerator pedal (HARD).2b. Fully release the accelerator pedal.3. Wait 7 seconds, fully depress the accelerator pedal and hold for approx. 10 seconds until the CEL starts blinking.4. Fully release the accelerator pedal (while the CEL is still blinking).5. Wait 10 seconds.6. Fully depress the accelerator pedal and hold for more than 10 seconds.7. Fully release the accelerator pedal (The CEL light will continue to blink).8. Turn ignition switch to "OFF" position and now you can start the car. The CEL light should be gone.If the CEL light continues to remain ON, repeat the above steps. Timing is extremely critical for resetting the ECU.Accelerator Pedal Release Position LearningOperation Procedure:1. Make sure that the accelerator pedal is fully released.2. Turn ignition switch "ON" and wait at least 2 seconds.3. Turn ignition switch "OFF" wait at least 10 seconds.4. Turn ignition switch "ON" and wait at least 2 seconds.5. Turn ignition switch "OFF" wait at least 10 seconds.Throttle Valve Closed Position LearningOperation Procedures:1. Make sure that accelerator pedal is fully released.2. Turn ignition switch is "ON."3. Turn ignition switch is "OFF" wait at least 10 seconds.Make sure that the throttle valve moves during above 10 seconds by confirming the operating sound.Idle Air Volume Learning (Throttle Position Learning)Operation Procedures:1. Perform "Accelerator Pedal Released Position Learning."2. Perform "Throttle Valve Closed Position Learning."3. Start engine and warm it up to normal operating temperature.4. Turn ignition switch "OFF" and wait at least 10 seconds.5. Conform that accelerator pedal is fully released, turn ignition switch "ON" and wait 3 seconds.6. Repeat the following (steps 7a, 7b) procedures quickly five times within 5 seconds.7a. Fully depress the accelerator pedal (HARD)7b. Fully release the accelerator pedal.8. Wait 7 seconds, fully depress the accelerator pedal and hold for approx. 20 seconds until the Check Engine Light (CEL) stops blinking and turned ON.9. Fully release the accelerator pedal within 3 seconds after the CEL is ON.10. Start engine and let it idle.11. Wait 20 seconds.12. Rev up the engine two or three times and make sure the idle speed and ignition timing are within the specifications.
