0
Which seals are you talking about? There are many seals on newer vehicles. For this reason I am going to assume you are referring to the front axle seals. I am assuming this because that is a very common failing seal on Chevy trucks. The easiest way to replace these seals is to completely remove the front differential housing. It's not as hard as it sounds. 1)Drain the gear oil out. 2)Remove skid plate 3)Unbolt the cv axle from front end 4)Disonnect front driveline (You may also want to remove oil filter at this time) 5)Unbolt front end from frame and roll out of the engine compartment. Knock axle stub shaft out of front end with hammer to access seal. Replace seals one at a time with OEM seal only. Aftermarket seals are usually the wrong seal, and they tend to leak. Be very careful when installing new seal, and be sure to lubricate sealing surface. Be careful when removing the longer shaft. There is a washer near the 4X4 actuator that can slide down, and you won't be able to get the shaft back in. If this happens you will have to unbolt the long shaft housing from the differential housing and put the washer back in place. Good luck.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What is the timing order and distributor cap setting for a 1996 Chevy pickup 5.7 liter engine?
Look at this: http://autorepair.about.com/library/firing_orders/bl-fo-5830.htm
What is interchangeable with a 1996 Ford Ranger?
a 96 Mazda pickup
1996 Chevy Blazer transfer case?
A 1996 Chevy Blazer Does have a transfer case IF it is equipped with 4 wheel drive
What is a Chevy 305?
The Chevy small block V8 305 cubic inch engine was manufactured between 1976 and 1996. It was used in cars and trucks.
Why does the 1996 Chevy Tahoe makes a rattling noise when accelerating cant tell if it is coming from the rear end or the front any ideas?
check the exhaust line one of the heat shield (metal plate between the pipe and the cab) migth be loose
Will a steering wheel from a 1996 Chevy pickup fit on a 1970 Chevy pickup?
NO it will not.
Where on a 1996 Chevy pickup 4.3?
Where what! What is your question?
Where is the alternator located on 1996 Chevy s-10 pickup truck?
You would find it in the front of the engine driven by the accessory belt.
Where is the 4 wheel drive actuator located on a 1996 2500 Chevy pickup?
It is screewed into the front Differential, towards passenger side but in the middle of the housing.
Will a 1996 Chevy s-10 4x4 transmission fit a 1996 Chevy 4x4 1500 pickup?
NO it will not. The bell housing is different.
Will a 1996 Chevy Tahoe 350 engine fit a 1988 Chevy pickup?
Yes but modification will be needed
What size motor is in a 1996 Chevy Silverado 1500 Pickup?
The Chevy SBC 5.7L 350cid V8 was the standard
Where is the carbon canister on a 1996 Nissan pickup?
on the right side in front
Where is the horn located on a 1996 Nissan pickup?
under front bumber.
How do you change a striker bolt on a 1996 Chevy pickup?
It just unscrews, It is real tight.
What kind of engine in 1996 Chevy 1500 4x4 pickup?
5.7 liter vortec.
Will rear end from 1999 Chevy pickup fit a 1996 Chevy pickup?
It depends on the gear ratio of the rear ends. You can find this out in the glove compartment of your truck. It should tell you there. Hope this helps you out.
