answersLogoWhite

0


Best Answer

The guiding rod is out of line, Motors getting gunked up, Roller track is off or the door is bent.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do get a garage door opener to work correctly it use to work well but now it does not open but a few feet and at times will not close?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Where is the learn button on the garage door?

nine times out of ten on the back the opener


How do you program your garage door opener in your 2002 Infiniti QX4?

1) Erase all your codes in the Homelink memory by pressing the two side buttons for 20+ seconds until the Homelink light flashes quickly. 2) Press and Hold your wireless garage door opener and the HomeLink button you want to program until the Homelink light flashes quickly. This will setup the Homelink opener temporarily. 3) Located and Press a scan button on the Garage door opener. Now press the button on the Homelink that you selected a few times (usually 5-8 times) until the garage door opens with the Homelink. Now its permanent. - I had this problem myself. I didn't have the wireless garage door opener so I used my keypad outside my home to program the HomeLink.


How do you program a sears garage door opener in your 2004 Envoy?

in the car, press and hold your garage button until it begins to blink, while holding your regular garage door opener near to envoy button. While pressing both buttons, the light should flash rapidly and then go out. You should then have succesfully programed it. If not, try it again, some times needs to learn codes for your garage.


How to Repair a Garage Door Opener?

Garage doors that open automatically are one of those conveniences we take for granted. When a garage door opener suddenly stops working, it can be extremely annoying. Here is a step by step guide to fixing your garage door opener. First, you should check to see if the cord that feeds power to your garage door opener is actually plugged into an outlet. This may seem too obvious, but this is a common reason why garage door openers do not work. If that doesn’t fix the problem, check your owner’s manual for some kind of lock feature. Someone may have inadvertently activated the lock feature, and that feature may be preventing the door from operating. The manual should tell you how to turn the lock feature off. If that doesn’t work, try unplugging the garage door opener and then plugging it back into an outlet a few times. This may reset the censors, allowing the opener to work again. If that doesn’t work, you should perhaps check to see if the batteries in your remote control for the garage door opener haven’t run out of power. If it still doesn’t work with new batteries, it is possible you accidently deprogrammed the remote control. Check the owner’s manual to learn how to reprogram it. If that didn’t fix the problem, check to see if the beam censor for your garage door opener is plugged in correctly. Next, try cleaning the censor itself. Its possible dirt, grime, or dust may have built up on the censor, preventing it from sending the signal to activate the garage door’s motor. Lastly, you should check to see if the chain that lifts up the door has been broken or become loose. If so, it is unfortunately not safe for you to try to repair it on your own. You should call an electrician who specializes in garage door repair. Until the repair man arrives, you are going to have to manually open the garage door yourself by either using a release cord or a handle. With these simple steps you can easily trouble shoot most problems that prevent a garage door opener from operating yourself.


How do you program the built in garage door opener Buick Riviera?

1. In the car, press and HOLD the outer two HomeLink buttons until the HomeLink light begins to flash rapidly. This will clear any old codes left in the car's controls. 2. Take the garage remote and hold it near the HomeLink buttons. Press and HOLD BOTH the garage remote and one of the HomeLink buttons until the HomeLink light begins to flash rapidly. Now your car has learned the proper garage door code, but you must get "permission" from the garage door opener itself before it will let the Buick open the door: 3. Climb up on a ladder and press the "Learn" button on the back of the garage door opener. WITHIN 30 SECONDS, get back into the car and press the programmed HomeLink button 3 times, for about 2 seconds each time. When the garage light flashes, your code is locked in! (Different door opener power heads have different routine to "learn" the HomeLink remote. Consult your owner manual for the door opener power head to program it to learn mode.) More specifics are available at homelink.com.


How do you remove code on garage door selling car?

You remove the code from the vehicle by holding down (up technically) on the first and third buttons, simultaneously. Watch for the light to change from solid to flashing after 1 min. However, in removing the code from the garage door opener mounted in the ceiling of the garage, you will need the original "clicker". With clicker in hand, you hold down on the setting button on the garage door receiver while also holding down on the "clicker" button. The garage door receiver light should flash several times to acknowledge the code. Test by using the clicker to open and close the garage door. Yours- Sarah Lee aka Mycarlady


Programming a Universal Door Opener?

A popular way to open garage doors is the universal door opener because it is compatible with a wide variety of door models. The universal remote can control both doors of a multi-bay garage and keep you from needing two separate remotes. Program the remote by holding down the buttons until the LED indicator turns red. Select the button that will be used to open the garage. Press and release that button the number of times that the instruction manual says is required for that door model. To finish the programming, hold the chosen button until the LED blinks.


How do I program my Honda Odyssey garage door opener?

New Car: Erase previous codes by pressing and holding two outside buttons for 20 s until red light flashes. Release buttons, proceed to step 1. 1. Unplug garage door opener from house current. 2. Hold garage door opener remote control 2 - 5 in from HomeLink keeping red light in view. 3. Select Homelink button you want to train. 4. Press and hold the button on the remote control and the button on the HomeLink at the same time and keep holding both buttons down. Canadian owners may have to press and release the remote unit every 2 seconds to keep the remote transmitting. 5. The red light on the HomeLink will begin flashing, slowly at first then rapidly. 6. When the red light flashes rapidly, release both buttons. 7. Plug in the garage door motor and test the the HomeLink transmitter by holding down the button you programmed. The door should operate. If it does not, then you may have a variable or rolling code garage door opener. Test this by holding the HomeLink transmitter button you just trained. If the red light blinks for two s then stays on, lucky you, you have a rolling code garage door opener. Not to worry, see below for Plan B! 8. Repeat the steps to train the other buttons on the HomeLink. TRAINING WITH A ROLLING CODE SYSTEM aka Plan B. 1. Complete steps 1-8 above first. 2. Find the 'Training Button' on the garage door opener unit. This may be on the back of the motor, or some units may allow training to be initiated from the wired remote unit in the garage itself. 3. Press and hold the training button on the garage door opener unit (or equivalent action as per the opener instructions). The light may blink or come on and stay on. You now have 30 s or so to press and hold the HomeLink button for 3-4 s (the very same button you trained above in steps 1-8) This should result in a signal of some sort from the garage door opener unit...the training light could turn off, the light on the opener could blink, etc. You may have to press the HomeLink button 3 or 4 times for the unit to recognize the HomeLink system. 4. Press the Homelink button again, the garage door system should operate!


How to program 1998 Nissan maxima gle garage door opener?

Hold the outside two buttons to clear the memory. Then hold in the button you want to program and the remote button to learn from at the same time. The blinking should change to a faster pace. No idea what makes this part happen. I must have done this step 50-100 times before it picked up my remote (maxim_83: this may depend on the learn-from-remote-control, but pressing and releasing the learn-from-remote-control as opposed to just holding it helped really well in my case; my maxima remote picked the signal up in seconds). After it picks up the signal, push the learn button on the garage opener. Then, push the visor button you programed. The garage opener light should flash and you will be done. A good idea would be to unplug the opener while you are trying to learn the code. I didn't and the repeated attempts overheated the opener. It's also less anoying to not have the door opening and closing a million times. Eventually, I was able to program both my garage doors. I still don't know what makes a difference. I didn't see any advantage to holding them both the 90 secs like they say it may take. Seems like the times it did finally take, it was in the first 15 seconds. I think it must be the newer frequency openers, because I had no problems with the older Craftsman openers. Thanks to the NIssan Forum for this


Set garage door opener in 7 series BMW?

Go to www.e38.org. Scroll down for the instructions. I did it on my 740il/2001 and works. It should be easy. try a few times until works. or try this: http://www.bimmerboard.com/forums/posts/689. Go BMW!


How to Work a Universal Garage Opener in the Car?

With the way technology has been evolving over the past few decades, especially with both wireless systems and remotes, it only makes sense that the evolution would find its way into vehicles as well. Cars these days are finding themselves built with an onboard system that will let them open their garage door without having to carry around the block-shaped controller. These onboard systems can be obtained from many popular manufacturers throughout the world and they are universal in that they can be configured to open nearly any garage. All you would need to do in order to configure your onboard system to your garage is to spend a few minutes in the car with your system and with the garage opener remote.Get into your car and bring the garage opener controller. Your system should have a pair of buttons on either side of it. Press them and let them go when you see the flashing light indicate that it is ready.Take your garage opener and hold it three inches away. Press the button that would normally open your garage and hold it down while you also press the button on the system that will be used to open the garage from here on out.When you notice the light is blinking more frequently, you may release both sets of buttons.Now you can hold down the training button that comes with your system. You will know that the configuration was a success if the light that was blinking before turns solid. If you do not see a solid light, you must continue with the next few steps.If the solid light does not appear, press the smart button that is behind your system, or it may be on the side, beside the lens for light and the antenna wire. This is the garage door motor.Go back into your car and press the button from before, holding it down for two seconds. Now you may release the button for training on your system. Do this about three times and your light should go solid, indicating that your configuration was a success.


What are the release dates for New Garage Explosion In Love with These Times - 2010?

New Garage Explosion In Love with These Times - 2010 was released on: USA: 20 November 2010 (internet)