Mercury Grand Marquis
Jeep Cherokee Sport
Jeep Liberty Sport
Social Network Websites

How do you change a back taillight?

202122

Top Answer
User Avatar
Wiki User
2005-11-05 05:19:29
2005-11-05 05:19:29

DEPENDS ON VEHICLE, FOLLOW THE WIRES INTO THR HOUSING AND DECIDE IF THAT IS THE ENTRANCE INTO HOUSING, LOK FOR BOLTS / NUTS./OR SCREWS THEN {EASILY] TWIST OR PULL THE SOCKET OUT AND TWIST OR PULL THE BULB OUT

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

how to change a taillight in a 2008 Nissan maxima

User Avatar

Open the liftgate Remove the 2 screws at the top of the taillight assembly Carefully " work " the taillight straight back towards you . There are plastic pins shaped >>>>>>>>>>>> that hold the taillight assembly in place The bulb sockets are a simple turn to remove / install

User Avatar

You just have to pull back the trim in the trunk to access the fasteners for the taillight assembly. Once you remove the taillight assembly just replace the bulb.

User Avatar

Open the rear hatch. you will see 2 screws on the side of the taillight. Remove them and pull the taillight out.

User Avatar

The entire taillight comes off as an assembly, and is not designed to be taken apart. To change a light bulb: 1. Inside the trunk look on the back side of the taillight near the quarter panel. There will be 3 nuts, the center nut holds the taillight assembly in place, remove that nut. 2. Pull the assembly rearward enough to bring the stud out from the header panel, then pull the tab out of the license plate light assembly. 3. Remove the socket that needs a new bulb and replace the bulb, then slide the taillight assembly back in place and put the nut back on.

User Avatar

Open tailgate. Remove 2 torx screws in side of taillight. wiggle taillight out, Remove hex screws that hold bulb assembly in taillight. change bulb, Reassemble

User Avatar

open the trunk, pull back the liner and unscrew the plastic wingnuts, pull out the taillight and un plug the connector

User Avatar

Open the trunk and disconnect the wiring lead.Remove the 10MM bolts on the taillight.Now you should be able to remove the light.

User Avatar

If you lift up the tailgate there are two screws that hold the taillight into place. If you unscrew those, the taillight will come off of the truck.

User Avatar

There's one screw on the outside holding the taillight on and also a wing nut on the inside of the car that you can take off by hand.

User Avatar

Remove the carpet protecting the back of the taillight Pull away foam cover Losen screw and remove taillight When done you should be able to unclick the electrical wires Afterwards click-off the back cover of the taillight and you will stand with the base of the light in your hand. Gently push down and counter screw the bulb to remove it. Recommended buying good quality light bulbs to replace.

User Avatar

The tail light bulbs are accessible from underneath the back of the truck, up inside the rear of the pickup box.

User Avatar

The 2006 Jeep Liberty rear tail light lens does not come off. The tail light is seal. You can access the tail light lightbulb through the back of the tail light, in the cargo compartment.

User Avatar

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops

User Avatar

open tailgate,look for two screws between light and tailgate,remove screws and pry out light pulling straight back.

User Avatar

To change the bulb in tour taillight, you must first remove the light and open it. You can usually remove the screws and pop it off. Then just replace the bulb and put back together.

User Avatar

Assume you mean taillights. Open the trunk, pull back the cover from the taillight, twist the bulb assembly counter-clockwise and the bulb assembly should come out.

User Avatar

it has wing nuts on it to hold it in place, it comes off by opening the trunk and the wing nuts are in back of the taillight inside the trunk.

User Avatar

very simple, open trunk, turn bulb socket to the left and pull socket and bulb from rear taillight, twist bulb out of the socket and install new bulb and install bulb and socket back into taillight and turn right to lock it in.

User Avatar

Open the tailgate.Remove the taillight bolts, pull taillight toward you to release two clips.Unplug the taillight connecter.Connect the taillight connecter.Install the pushing away from you to fasten the two clips.Install the taillight boltsClose the tailgate.

User Avatar

I believe you have to unscrew a couple bolts on the inside of the truck bed to get the taillight assembly off the truck then you can unscrew the light sockets and replace the burnt out bulb

User Avatar

Inside the trunk there is a trim panel that needs to be removed that covers up the taillight bolts. Remove the trim panel and then you can remove the two bolts that hold in the taillight. I have also included an instructional video that will show you how this is done. Hope this helps, 1ATony

User Avatar

raise hatch, pull back carpet. unscrew the 5 polastic screws holing in the taillight. twist and remove light. install is reverse.

User Avatar

taillight is one word.

User Avatar

in the back trunk, usually on the right side near the taillight~


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.