0
How do you change a flywheel for a 1979 Ford F100 with a 302-6cyl and an automatic transmission?
Wiki User
∙ 16y ago
THIS IS HOW IT'S DONE ON A 1998 CHEVY 1500 AUTOMATIC... I THINK IT SHOULD BE CLOSE TO THE SAME. NOT SURE THOUGH!!! You have to unbolt the tranny from the engine........ followed by the bolts out of the back of the fly wheel....... then unbolt the place where the frame meets from the rear to the frontend.... hook a cable crank to the rear axel and one of the cross supports of the front frame........ slowly draw the frame back with the crank until you have enough room to take the old one out and put the new one in. BE SURE TO HAVE A FLOOR JACK UNDER THE TRANNY SO IT DOESN'T DROP!!
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do you change the flywheel on a 1991 suburban?
automatic? remove transmission and torque converter then remove flexplate (auto has a flexplate not a flywheel if mauel transmission remove gear box and clutch then remove flywheel
Is there an adapter you can use to mount a clutch type flywheel to an automatic crankshaft end Is there anything you can do beside changing the crank?
For most engines there is no need to change the crankshaft to use an engine for an automatic or a manual transmission. For an automatic, connect a flex-plate to the crankshaft. For a manual transmission connect a flywheel.
Do you have to change the flywheel when you change an automatice transmission to a manual transmission?
Yes.
How do you change flywheel on 97 Tahoe 4x4?
Remove the transmission unbolt the flywheel and replace.
Are the engines in a 1992 Geo Metro with manual transmissions interchangeable with engines with automatic transmissions?
Yes, they are. Please remember you have to also change the flywheel on the manual with the flexplate from the automatic transmission/tourque converter. you might also have to change the axles too.
How do you change the flywheel on a 1978 gmc truck?
remove starter remove transmission unbolt flywheel
How is the fly wheel placed in a standard transmission vehicle and an automatic vehicle?
For both manual and automatic transmission equipped vehicles, the flywheel is actually attached to the rear of the engine crankshaft, not to the transmission itself. But cars that have automatic transmissions originally can have flywheels that are not compatable with manual transmissions. That is because with an auto trans the torque converter is bolted onto the flywheel, and there is no need for a central hole and bearing or bushing in the exact center of the flywheel. On the other hand, with a manual transmissioned car there is a pressure plate bolted to the flywheel, and a clutch plate is sandwiched between the pressure plate and the flywheel. There is also a shaft from the transmission thru the bell housing, through the center of the pressure plate, attached with a toothed surface to the clutch plate, and then the extreme forward point of this shaft goes into a hole in the center of a flywheel, and is held in place by a pilot bushing or pilot bearing that has been pressed into the center hole of the flywheel. So if you take out an automatic transmission and torque converter, you might not be able to bolt in a manual transmission because there might not be a central hole in the original flywheel to hold the pilot bearing/bushing and the tip of the pilot shaft....You may need to also change the flywheel.
How do you change the flywheel on a 2004 suburban?
You will have to remove the transmission 1st. After doing that then just unbolt the flywheel and replace it.
How do you change a flywheel for a 1998 Ford Contour?
flywheel replacement generally requires removal of the Transmission and Torque Converter .
Can you put an automatic transmission on a 250 straight 6?
The auto transmission will have to have the proper bell housing to line up. The cross member will need to be changed along with the flywheel. you will also need to add a cooler, and possibly change the radiator.
What is needed to change a 1996 Dodge Avenger automatic transmission to a manual transmission?
flywheel ,clutch plate, pressure plate,release bearing,gear box,lever,mounting,clutch pedal.clutch pump 2,....good mechanic
Can you change an automatic transmission car to a manual transmission car?
yes you can ,but you will need to buy and have installed, a new flywheel, bell housing, transmission, clutch, and drive shaft. then you will also have to have installed a clutch pedal inside the car. and to top it off, it the car has a computer, you will need to buy a computer to match a standard shift instead of an automatic shift. cheaper just to change cars
