Brakes and Tires
Headlights Tail and Brake Lights
Dodge Caravan
Dodge Grand Caravan

How do you change a tail light on a dodge caravan?

343536

Top Answer
User Avatar
Wiki User
2006-02-19 11:41:29
2006-02-19 11:41:29

Like most newer vehicles changing a bulb is heck, open the rear hatch and remove the screws that hold trim around the bottom between the weather stripping and carpet...also the trim behind the brake light you want to replace,,,once this is done youll have to remove the trim and the pannel behind the light to be replaced,,,,there will be several screws that need to be taken out....then pull the brake lamp house out,,,,yes the hole lamp house will come off the van,,,then just pull the bulb and replace....reverse steps and your done....dont you just love chrysler.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Have a look at this link: http://www.wikihow.com/Replace-a-Tail-Light-on-a-Dodge-Grand-Caravan

User Avatar

remove tail light, remove burnt bulb, replace burnt bulb, test if it works, then put tail light back on....

User Avatar

From outside,take a screws out to get light assembly loose and remove light socket from back of assembly and channge your light bulb,then put it back.

User Avatar

See sources and related links below for the correct tail light lamp bulb part numbers.

User Avatar

See sources and related links below.

User Avatar

The tail light is an assembly. The lens is not removable. To replace a bulb you remove the assembly by opening the liftgate, removing two fasteners, and pulling the light rearward.

User Avatar

Open liftgate. Beside lamp housing are push pins. Pry them out while holding lamp in place so it won't fall out.

User Avatar

I need a answer to my question. Thanks

User Avatar

RAISE THE REAR HATCH, ON THE IN SIDE BY THE LIGHT YOU WILL SEE 2 SCREWS, TAKE THEM OUT AND PULL COMPLETE LIGHT ( IF LEFT SIDE l BACK AND TOWARD THE LEFT, IF RIGHT SAME THING BUT TOWARD RIGHT)

User Avatar

To change your Durango's tail light, first make sure to have a flat head screw driver and a new bulb. You will then open your trunk and remove the screws to the tail light, swap out the bulbs and replace the housing case.

User Avatar

Probably a bad bulb They are double filamented with the smaller filament for stop and turn Larger is for tail light

User Avatar

Go to the following web address: http://www.discountcarlights.com/catalog/index.php?N=1607+10151+4294963218&Ntt=dodge%20grand%20caravan%20tail%20light

User Avatar

the tail light is screwed in from the inside of the bed of the truck

User Avatar

how to change tail light bulb on Toyota sequoia

User Avatar

How do you change the tail light on a 2001 toyota sequoia

User Avatar

Housing/Lens or bulb? If bulb, then see Sources and Related Links to see if both take the same bulbs.

User Avatar

# Remove the screws and detach the tail light housing # Rotate the bulb holder counterclockwise and remove it from the back of the housing.Press the tabs and pull the bulb from the holder

User Avatar

on all dodge trucks the way you change the bulbs is simply unscerew the tail light assembly and remove it from the rear of the vehicle and you will see your lightbulb fittings right on the back of the light assembly

User Avatar

It might be a dodge intrepid. The 1967 Dodge Charger had one long tail/brake light .

User Avatar

On my 2005 Dodge Ram Daytona. I had to open the tail gate, remove the two screws on the jam next to the light assembly. After removing the assembly, there is a light bar held by six screws. After removal of these, you can select the bulb you wish to change and then reassemble to install light assembly.

User Avatar

on the tail light problem - unbolt the tail light from inside th truck -the hold tail light assemble will come out - it is recommended to change all the blubs your all ready there

User Avatar

open the hood, head light is held in place by screws from the top, tail lights are held in place by two pins you see when the back door is open

User Avatar

Open the trunk. Access to the tail lights is from there.

User Avatar

Definitely sounds like an earth problem from your turn indicator. Check your earth wire from the light cluster especially from the turn signal. If necessary splice in a new wire to a good earth point this will stop the tail light flashing.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.