answersLogoWhite

0


Best Answer

This one is very easy. Corner light cover is held in with just one screw. Lift hood and just above corner light you will see tab from light with screw connected to frame. Take out screw and light cover can be taken out. You will see wires connected to bulb assembly. To replace bulb, unscrew assembly from cover with twisting motion. Replace bulb assembly into new corner light cover and return new corner light cover to its place...put back screw in tab...done. Hope this helps

User Avatar

Wiki User

โˆ™ 2006-04-01 14:40:04
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you change the corner light cover on 1999 Mazda Protege?
Write your answer...
Submit
Related questions

Where is the horn on a 98 Mazda Protege?

Well I had a 1995 Protege but I think is on the same place. It's beehint the right corner of the front cover. You have to remove the black cover under the car to see it. Mazda hide pretty well.


Where is the horn in a 1996 Mazda Protege?

Just behind the right corner of the front bumper. You have to remove the black cover under the car to see it. Mazda hide it pretty well.


Where is the pcv valve on a 1993 Mazda Protege DX?

it should be at top left corner of valve cover go to auto parts store for manual about $15.


Where is the Diagnostic port on a 1992 Mazda Protege?

Near the battery. It will have "DIAGNOSTIC" on the cover.


Where is the dipstick located on a 1991 Mazda protege 323?

IF ITS A 1.8, THEN ITS NEXT TO THE TIMING COVER


Where is the PCV valve located on a 1998 Mazda Protege 4 cylinder?

On my 1997 Protege a hose runs from the valve cover to the air intake assembly. Where the hose connects to the valve cover is the PCV valve.


What is the valve cover torque on a 2000 Mazda Protege 1.8L?

The 2000 Mazda 1.8 liter engine valve cover torque specification is 45 pounds. The valve cover bolts should be torqued in 15 pound intervals.


Where is the camshaft sensor CPS in a 1.6L 5-speed 2000 Mazda Protege?

on the cover of the timing belt


Where is the water pump located on a 2000 Mazda Protege?

It is under the timing cover and driven by the timing belt. Anytime you change one it is best to replace both as far as cost is the same.


Where is the PCV valve on a 1999 Mazda Protege?

on 99 models with 1.8 liters on top of engine in center of valve cover


Where is the horn in a 1995 Mazda Protege?

I you mean haw to make it to sound: On the side of the steering wheel, at about 3:00 and 9:00. If you are asking about the horn, its located behind the right corner of the fron bumper. You have to remove the black cover that it under the car. Mazda put hard encourage in hiding it .


How can I find out what each of the fuses are used for 2000 Mazda Protege?

if you look on the back of the cover of the fuse box it should have a diagram with labels for all the fuses


Where is a Mazda protege 2001 fuel injector located?

The fuel injectors are located under the fuel rail, between the intake manifold and the valve cover.


Where can you get a picture of a fusebox diagram of a 1996 Mazda protege for the radio fuse?

Try looking on the back of the fuse box cover, there is often a diagram there. If not it should be in the owner's manual.


Where is the access cover for the flywheel and drive belt on a 1992 Mazda protege?

at the back of motor in front of transmission at the bottom have to remove 4 , 10mm bolts hope this helps


How do you fix a Mazda Protege with a bad crankshaft sensor?

locate the crankshaft sensor which will probably be behind or right next to the crank shaft which is under the timing belt cover you might have to take the cover off and the timing belt


Where is knock sensor on 02' Mazda-Protege 2.0?

Its in the middle of the block and an inch or two down from where the head meets the block. Alternately, You can follow the wire to it, which is clipped in the corner space between the valve cover and the intake manifold (on the passenger's side of the intake manifold and towards the firewall from the valve cover). It should be the only wire on the side leading to the block.


How do you adjust the parking brake on a 1995 Mazda Protege?

I have a manual 96 Mazda Protege, with the parking break located behind the shifter. The adjustment bolt is located right next to the parking break on the left side (drivers side) of the parking break handle. you will have to remove the rubber cover around the parking break shaft in order to see the bolt.


Where is the water pump located on a 1998 Mazda Protege?

The water pump is under the timing belt cover. To access the water pump, you must first remove both belts, the water pump pully, and the timing belt cover.


What does it mean when there is oil in the air cooler on a Mazda millenia?

Change the PCV valve located on the valve cover


What is a timing cover seal and where is it at on a Mazda 929?

What is a timing cover seal on a 1992 mazda 929 and where is it located at?


Where is the cam sensor located on a 2001 Mazda protege es 20?

The cam sensor is located on the left side of the engine (as your looking at it) on the valve cover. It is the only sensor that is located on that side on the upper part of the engine.


On a 1993 Mazda protege what is the small rubber hose that connects from the air intake hose to the valve cover on the front right side not the pcv valve hose?

Its called breather hose. It will cost you less than $ 10.00.


Where is timing belt on 2001 Mazda protege 2.0l?

left hand side of the motor...in the silver casing. will have to take off the valve cover and all to get to it...it is a PAIN! I am trying to find the timing marks for a 2001 2.0 mp3


Where is the main relay on a 2002 Mazda Protege?

The main relay is in the fuse panel located under the hood on the driver's (left) side. Original equipment relay is green. Schematic decal is on the inside of the fuse box cover.