answersLogoWhite
American Cars
Brake Pads and Rotors
Chevy Silverado
Toyota Tundra

How do you change the front rotors on a 1998 s -10 blazer?

123

Top Answer
User Avatar
Wiki User
Answered 2013-06-16 16:53:11

Raise it up on jack stands, disconnect the brake line, pinch off the brake line with a set of vice grips, unbolt the calipers. The rotor simply pulls out at this point.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Your Answer

Related Questions


Change front brake rotors on a 1998 Hyundai Accent?


wear gloves, bearings all come out. then you have to remove the sensor off the back of it. along with 6 17mm bolts. How do you change the rotors in the front on a 1998 Isuzu Trooper


They are free floating rotors , Remove the caliper and the rotors should pull off. If not they may be gaulded on and you will need to use a hammer to help them off


The fuel gauge fuse on 1998 Chevy blazer is located in the front of the blazer. It is on the driver side next to the hook latch.



1998 Chevrolet Blazer did not have vent windows.


Front or rear rotors and 2 wheel or 4 wheel drive, it makes a difference.


Some versions had rotors all around, but 99% of these trucks had rear drum brakes.,,,,,,,,,,,disc and rotor brakes are the same thing, they are the ones that are squeesed from both sides with pads and A calliper, DRUM brakes are the ones that have "shoes" on the inside pushing outward.Hope this helps, Jamison.


Tap on your 1998 Mazda brake rotors with a hammer or mallet until they become loose. The brake rotors will simply slide off.


It is located in the fuel tank.


on the intake manifold front of motor on top


How_much_does_it_cost_to_replace_brakes_and_Rotors_on_a_1992_Toyota_Camry


How do you change a 1998 jimmy 4X4 front wheel bearing ?


Need to know what is wrong with it to answer that question.


The ERG valve is located on the front of the engine on a 1998 Chevy Blazer V6 4.3L. It is near the top bolted to the intake manifold.


Removing Front & Rear Rotors Well Guys... I remove my Front & Rear Rotors out of my 1998 Ford Expedition XLT. I rented a 3 Jaw Puller from Auto Zone and a bottle of PB Blaster and a sledge hammer it only took about one hour or less to take both off... The way I removed the Front & Rear Rotors was ... 1. I put lots of PB Blaster in the back and the front of the rotors to be removed. 2. I put plenty of tension with the 3 Jaw Puller... 3. I hit the back of the rotor with the sledge hammer... And it came right off... Hope this helps someone out there...


try spitting on the front rotors. This helped and my brakes are like new


2 wheel or 4 wheel drive makes a big difference.



Check your owners manual, it will tell you in that.


HOW TO GET A PULLEY OFF A 1998 CHEVY BLAZER


Removing Front & Rear Rotors Well Guys... I remove my Front & Rear Rotors out of my 1998 Ford Expedition XLT. I rented a 3 Jaw Puller from Auto Zone and a bottle of PB Blaster and a sledge hammer it only took about one hour or less to take both off... The way I removed the Front & Rear Rotors was ... 1. I put lots of PB Blaster in the back and the front of the rotors to be removed. 2. I put plenty of tension with the 3 Jaw Puller... 3. I hit the back of the rotor with the sledge hammer... And it came right off... Hope this helps...


Removing Front & Rear Rotors Well Guys... I remove my Front & Rear Rotors out of my 1998 Ford Expedition XLT. I rented a 3 Jaw Puller from Auto Zone and a bottle of PB Blaster and a sledge hammer it only took about one hour or less to take both off... The way I removed the Front & Rear Rotors was ... 1. I put lots of PB Blaster in the back and the front of the rotors to be removed. 2. I put plenty of tension with the 3 Jaw Puller... 3. I hit the back of the rotor with the sledge hammer... And it came right off... Hope this helps someone out there...


Removing Front & Rear Rotors Well Guys... I remove my Front & Rear Rotors out of my 1998 Ford Expedition XLT. I rented a 3 Jaw Puller from Auto Zone and a bottle of PB Blaster and a sledge hammer it only took about one hour or less to take both off... The way I removed the Front & Rear Rotors was ... 1. I put lots of PB Blaster in the back and the front of the rotors to be removed. 2. I put plenty of tension with the 3 Jaw Puller... 3. I hit the back of the rotor with the sledge hammer... And it came right off... Hope this helps someone out there...


Tucked into the quarter panels on the front of the car



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.