answersLogoWhite

0


Best Answer

the steering column is mostly screws so that isn't a biggie however becareful of the airbag (special prep. steps have to ba taken because of this anyway to your question ,1) disconnect neg battery cable,2)you are going to have to remocve steering column covers,3)remove the screw holding the switch

User Avatar

Wiki User

โˆ™ 2011-09-13 00:23:21
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you change the ignition switch on your 93 probe GT?
Write your answer...
Submit
Related questions

How do you change ignition switch on a 93 Honda Accord?

how to change manual ignition switch on a 93 Honda accord


How do you change iginition switch on 93 dodge caravan?

how do caravanu change ignition switch in 93 dodge


How do you change the ignition switch on a 93 Nissan quest?

Begin by removing the retaining ring at the top of your 1993 Nissan Quest ignition switch. Slide the ignition barrel out. Remove the wiring harness from the end of the ignition barrel. Reverse the process to install your new ignition switch.


Where is the coil on a 1993 Ford Probe gt?

On the '93-'97 GT's the ignition coil is part of the distributor. If your coil goes bad you need to change the distributor.


Where is the kill switch on 93 Maxima?

It is controlled by the ignition key. It has no inertia switch if that is what you are asking about.


How do you replace the ignition switch on a 93 2500 Chevy?

You switch the carborator with the ac and then rewire the inside to the dashboard


My 93 probe has the fuel cut out switch on and refuses to start. how do I fix it?

are you sure its fuel cut out? my probe would not start traced problem to electronics inside distributor had failed [common fault on probe]


How do you remove and install the ignition switch on a 91 Ford Explorer?

I am working on changing my 93 Explorer ignition switch now. As soon as I figure it out I will let you know. :-) Still working on it.


On a 93 Chevy cavalier- do you have to pull steering wheel to replace ignition switch?

yes


Does a 1995 Ford Probe have r12 or 134a?

It has 134 A the change was around 92 93


93 Honda Accord EX Sedan key won't stay on?

Could be a bad ignition switch


Where is the fuel pump reset switch located on a '93' Ford Probe?

If you are talking about the inertia switch, it is in the hatch on the driver's side under the floor mat behind the wheel well.


Can I replace ignition switch on my 93 Buick Lesabre?

yes u can all u need to do is go to a car store and buy the parts that you need for the ignition switch and put it in and it shud work i am a son of a machanic.


Why would my 93 probe gt fuel cutout light come on and die bypassed inertia switch changed fuel pump and filter now just no spark to plugs even after replacing dist cap and rotor?

my 1993 probe gt done the same thing with the no spark at the plugs the ignition module was bad i replace the whole distributor and it runs great


Will the Ford Probe GT raise your car insurance?

No it won't. I had a 95 Ford Probe Se 2.0L and when the transmission went i upgraded to a 93 Probe Gt 2.5L V6 and my insurance didn't change at all. I love the car.


Where is the dashboard light located on the 93 Ford Probe?

are you thinking about the dimmer switch or the actual illumination light? on the left side of the steering wheel you will find the dimmer switch, and the dash becomes illuminated from the first click of your headlight switch.


How do you remove the ignition switch from a 93 ford explorer?

The steering wheel has to be removed since it has Air bags this MUST be done by a professional


How do you change ignition on 93 Ford Taurus?

Ignition what?CoilControl moduleSwitchLock cylinderSee "Related Questions" below for more


How do you replace the ignition distributor on a 93 mx6 v6?

How do you replace the ignition distributor on a 93 mx6 v6 pics?


How do you remove and replace the ignition switch in a 93 LeBaron?

to replace the switch u will need the key to the old ignition switch. its as simple as getting a t15 bits to take off the steering colum and unscrewing the switch i think the bit size is t25 and you need a special bit with a hole in the center of it. you take off the steering wheel column covers.


Will a 92 Ford Probe front window fit in a 93 Ford Probe?

no, they are different body styles.


Was there a recall on the ignition switch for a 93 caprice?

Join http://www.totalrecallinfo.com for FREE, and click the LINKS tab. They have the BEST database, past or present.


How do you change the ignition switch on a 92 Mitsubishi Mirage hatchback?

I changed the whole ignition in a 93 colt. I got the replacement from a lancer!The ignition wraps round the steering column and is bolted with sheer away bolts. The bolts are designed to break when originaly tightend (Antitheft). you will have to use a hacksaw blade to cut slits in the top of the bolts that are on the suspect ignition. when slits are deep enough, use a flathead screwdriver to remove them. You will have to get new bolts from your Mitsubishi dealer. when its off the ignition switch is held by a Philips screw, remove and continue with putting the replacement ignition on! hope it helps!!


Will a radiator from a 91 Ford Probe fit in a 93?

no


Can an '89gt Ford Probe transmission go in a 1994 or'96 Ford Probe?

no, the 89-92 engine/transmissions are different from the 93-97 ford probe.