answersLogoWhite

0


Best Answer
Copy

1. Remove the hot wire from the battery. Move it to the side of the battery were it will not hit anything. 2. Remove the Wire in front of the starter (the starter is at the back of the engine on the bottem side on the passenger side). 3. Remove the 3 bolts (they are the 3 bigest bolts)on the starter. The starter should fall off at this time if not just pull it off. The 3 bolt go thur the starter into the transmission.

To put it back in do the reverse and start with 3 and go to 1.

Always remove ground wire. If the hot wire accidently finds power, even a little, watch out. The ground will have more trouble finding a GOOD ground.

User Avatar

Wiki User

โˆ™ 2015-07-15 21:03:44
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you change the starter on a 1988 Ford Ranger 2.0 ltr engine?
Write your answer...
Submit

Related Questions

Where is the starter located on a 1988 Ford Ranger truck?

Lower rear end of the engine


How do you change a starter on a 1988 Toyota Cressida?

Change a starter on a 1988 Toyota Cressida


Why cant i get fuel to engine on a 1988 ford ranger?

Either change fuel filter or fuel pump...


Where is the starter located on a 1988 Nissan Stanza?

The starter on a 1988 Nissan Stanza can be found on the inner side of the engine. It is between the gear box and the engine block.


How do you change starter on a 1988 Toyota Corolla sedan?

In the back of the engine one bolt is hidden under the air box


Where is the starter on a 1988 Acura Integra rs?

You can find your 1988 Acura Integra starter on the right hand side of the engine. You can follow the positive battery cable directly to the starter.


Where is the map sensor located on a 1988 ford ranger 2.9l?

On the engine.


Where is the starter on a 1988 Acura Legend?

the starter is located at the right side of the engine if you r looking at it from the front the starter is located at the right side of the engine if you r looking at it from the front


Where is the starter solenoid located on a 1988 Ford Ranger?

It should be attached to the short positive battery cable.


Where is the starter on a 1988 Chevy corvett?

At the rear lower end of engine


How do you change the starter in a 1988 Isuzu Trooper?

to change the starter for Isuzu trooper is easy way to oper the exhaust pipe first.then you can reach easly to starter.


How much horse power does a Ford Ranger XL 1988 2.9?

I believe the 2.9 liter V6 engine in a 1988 Ford Ranger is rated at : ( 140 horsepower )


1988 Ford Taurus the starter wants to keep running?

The starter solenoid is not disengaging once engine is started. Rebuild starter or replace with a new starter.


How do you take out a starter on a 1988 Nissan pickup with a v6 engine?

remove neg.cable.then positive cable cable from starter,remove male to female wire ,then remove 2 bolts holding starter to engine.


What is the oil capacity for a 1988 ford ranger 2.9 v6 engine?

5 quarts


On a 1988 ford ranger where is the oil pan?

The oil pan is bolted to the bottom of the engine


V6 2.9L Ford Ranger 1988?

Yes , there was a 2.9 litre V6 engine available in a 1988 Ford Ranger , as well as the 2.0 and 2.3 litre four cylinder engines


Where is there a fuse for the power source to a 1988 Ford Ranger It is not getting any connection to the battery or starter or where is the power distrubtion box?

Looking into the engine . . . right side near the firewall should be a large fuse box.


What does the starter module look like on a 1988 Ranger?

On the 84 is looks like a rectangular block plugged into the base of the distributer.


How do you change the starter on a 1988 Nissan pickup?

disconnect neg. battery cable ,remove pos.cable from starter .10 or 12 mm wrench.remove wire from starter ,no wrench needed,its a male to female connector,remove 2 bolts holding starter to engine,12 or 14 mm wrench,thats it.


Where is and How do you change the starter in a 1988 ford escort?

under front of engine. to remove dissconect battery. lift car and support .disconect wire from starter. lossen two bolts holding starter . becarful sometimes those starters have shimes so if it does make sure you replace it .


Where is the starter on a 1988 Plymouth reliant k?

It is on the back of the engine, under the intake.It is on the back of the engine, under the intake.


Where is the knock sensor a 1988 2.8 liter?

It should be on the side of the engine block over by the starter.


What is the firing order on a 1988 ford ranger 2.0 liter engine?

1-3-4-2


How do i replace a speedometer cable on a 1988 ford ranger 4wd with a 2.9 engine?

You can replace the speedometer cable, on your 1988 Ford Ranger, by loosening the cable nut on each end of the cable. The cable will come off and can then be replaced.