0
Want to try de-waterlogging yourself? Here's how to do it right!
- Turn off the power to the pump at the switch or breaker. Also if there is a valve between the pump and the tank, turn it off. If this valve is broken or leaking, now is an excellent time to change it; if the pressure gauge needs replacing, do that also, after step 2!
- Open a faucet close to the tank, preferably one that is as low to the ground as possible to facilitate draining.
- When the water slows to a trickle, find a way to introduce air into the tank. This may be done by taking out a fitting or plug in the side of the tank, preferably close to the center of the tank, or using a small air compressor to put air into a tire valve-style fitting on the side or bottom of the tank. Either way, the idea is to get most of the water out of the tank, and replace it with air. If your pump motor is in the well, you can empty the tank of water completely without problems. If you have a jet pump, where the motor is visible next to the wellhead, you should leave about 1/2 of the water in the tank, in order to keep some water for priming the pump. In fact, it is a good idea to fill several buckets with water before you turn the pump off, just in case! NOTE: Do not pressurize the tank with air instead of draining it - you can put too much air into the system, and cause some rather interesting problems and no end of frustration for yourself!!
- When you have sufficient air in the tank, turn off the air and faucet, and turn the pump back on. Open the valve between the pump and tank just enough to keep the pump running, but do not let the pressure drop below 20 lbs. until the tank is full.
- If you can't get it running right, call us (or your nearest pump professional)!! We'll gladly help you over the phone if possible, or give you a hand in person, if you are in the local area
You didn't say if this is a galvanized tank or a bladder tank. There is a large difference between the two. Is your tank painted with a name on it? If so what name and model # if possible?
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you recharge a water logged pressure tank?
if its a bladder type tank, it will need to be replaced
How do you tell if your water tank is water logged and what are the symptoms of the water well pump if this occurs?
if your water tank is water logged the pump will kick on almost immediatly when the water tap is opened, and will kick off shortly after it is closed. Water cannot be compressed. The air inside the tank allows the pump to "catch up" and shut off while the water is in use, and allows for a steady flow of water at similar pressures.
What does it mean when there are Short intervals between activation of a well pump usually means that the system is?
The pressure tank is likely "water logged". It has lost the air inside the pressure tank.
How do you spell loged in?
The term is spelled "logged in" (from the listing in a log, also login file).
What actors and actresses appeared in Water-Logged - 1962?
The cast of Water-Logged - 1962 includes: Bruce Brown as Narrator
What is the correct way to measure the height of a gas water heater?
From the floor to the top of the tank
How do you dry out a water logged caravan?
Get a hairdryer on it.
What are the release dates for Endurance - 2002 Water Logged - 1.8?
Endurance - 2002 Water Logged - 1.8 was released on: USA: 7 December 2002
What are the release dates for Forensic Files - 2000 Water Logged?
Forensic Files - 2000 Water Logged was released on: USA: 10 December 2010
Well tank is not holding any water and when faucet is turned on pump cycles on and off for 2 or 3 seconds at a time?
Your holding tank is "water logged". There is an air bladder in the tank that requires a specific pressure (dependant on the tank size). Some possible causes are a loss of air in the air bladder (just like a tire looses air over time), or the bladder has a tear or hole in it.
How do you bleed a bladder tank?
bleed the air tank by pushing down on the air stem, remove the pressure from the water tank,add correct amount of air to bladder, then start pump.
What is the correct path of light ray shinning in the surface of a tank filled with water?
ano ang adwana
