How do you fill the transmission fluid on a 1988 Jaguar XJ6?

Where do you fill the transmission fluid on a 88 F250 diesel?

You fill the transmission fluid on the 1988 F250 diesel at the dipstick of the transmission. You will need a filler funnel in order to keep spillage to a minimum.

How many quarts are required to fill an 88 Toyota Camry transmission?

The 1988 Toyota Camry transmission has a fluid capacity of 6.3 quarts. You can check the transmission fluid level with the transmission fluid dipstick.

Where do you fill the transmission fluid on a 1979 Oldsmobile toronado?

You fill transmission with fluid through the transmission fluid dipstic tube

How do you fill transmission fluid on a 1988 crown Victoria?

Thru the transmission dip stick. use a funnel to get the fluid into the dipstick tube and check to make sure you do not overfill.

How do you fill the transmission fluid in a 1988 Oldsmobile Toronado?

Thur the dip stick..... Thur the dip stick.....

Where to fill transmission fluid?

I have a 1951 flathead fordomatic automatic station wagon. Where do I fill the transmission fluid?

Where do you fill the transmission fluid on a 2004 gmc safari?

Where do I fill the transmission fluid gmc Safari van?

Where is the transmission fluid dip stick in a 5 speed 1988 Ford Ranger?

Ford manual transmissions do not have dipsticks like most Ford automatics do The manual transmission fluid level is checked at the fill plug on the transmission

Fill transmission fluid on 1993 BMW 740i?

and what type transmission fluid

What happens if you over fill your transmission fluid?

If you over fill your transmission fluid, you might blow out the transmission seals. It is most likely that some fluid will overflow, but no damage will occur.

How do check transmission fluid for 2005 Jaguar?

Transmission Fluid Level CheckSpecial Service ToolsCheckThe follow steps must be observed before starting the transmission fluid level check.The vehicle must be on a horizontal ramp.The parking brake must be applied.The engine must be running for 2 minutes with the transmission selector lever in the "P" position.Connect the Jaguar Approved Diagnostic System.Make sure the transmission selector lever is in the "P" position.NOTE: Make sure the transmission fluid temperature is below 30°C (86°F) on the Jaguar Approved Diagnostic System.With the engine running and the foot brake applied, circulate the transmission fluid by:Moving the transmission selector lever to the -R- positionWaiting for three seconds.Moving the transmission selector lever to the -D- positionWaiting for three seconds.Moving the transmission selector lever to the -P- positionRaise and support the vehicle.Remove the transmission undertray.Place a suitable container under the transmission fluid filler plug.WARNING: Make sure that care is exercised near rotating parts. Failure to follow this instruction may result in personal injury.With the engine running, using the special tool remove the transmission fluid fill plug.Remove and discard the transmission fluid fill plug.NOTE: Use transmission fluid meeting Jaguar specification.If the transmission fluid does not come out of the transmission fluid filler plug hole the transmission fluid level is insufficient. If this is the case add the transmission fluid in 0.5 liter units into the transmission fluid filler plug hole until fluid comes out.NOTE: Make sure the transmission fluid temperature does not exceed 50°C (122°F) . If the transmission fluid temperature does exceed 50°C (122°F) stop the transmission fluid level check and allow the transmission fluid to cool until the temperature is below 30°C (86°F) .Allow the transmission fluid to drain from the transmission fluid filler plug hole until the flow almost stops.NOTE: Install a new sealing washer.Using the special tool, install the new transmission fluid fill plug.CAUTION: Make sure the transmission fluid fill plug is tightened to the correct specification. Failure to follow this instruction may result in damage to the vehicle.Using the special tool and a torque wrench, tighten the transmission fluid fill plug.Tighten the transmission fluid fill plug to the torque given by the calculationTo make sure the transmission fill plug is torqued to the correct specification. Using the special tool and a torque wrench the following calculation steps must be followed. Step 1. Multiply 35 Nm by the effective length of the torque wrench (1).Step 2. Add the effective length of the special tool (2) to the effective length of the torque wrench (1).Step 3. Divide the total of step 1 by the total of step 2.Step 4. Set the torque wrench to the figure arrived at in step 3.Tighten the transmission fluid fill plug to the torque given by the calculation.Remove the special tool.Remove the container.Install the transmission undertray.Lower the vehicle.Disconnect the Jaguar Approved Diagnostic System.

How much fluid is needed when replacing transmission filter on 1988 D-100 Dodge Ram?

6-7qts approx. fill