0
the clutch on the 626 is hydrolic like on the mx6 you have two chioces if its the cylinder and not the lines or transmission choice one replace hole cylinder cost 65 dollars plus choice two try to find a rebuild kit cost 15 dollars plus the rebuild kit should have all the enter workings of the cylinder and they are easy to put together
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
Where do clutch fluid goes in a Ford Escort?
Clutch master cylinder, usually located near the brake master cylinder. ------------------------------------------------------------------------------------------------ I chose the ( 1996 and 2003 ) Ford Escort owners manuals to look at and they show that the brake master cylinder is also used for the hydraulic clutch
How do i replace a clutch master cylinder in a 1996 Honda civic?
how difficult is it to replace the MS on a 1996 Honda accord
Does a 1996 Ford Escort LX 5 speed have a hydraulic clutch w only 20K miles that can be owner serviced or adjusted and where is the master cylinder for it?
I have a 1995 an the hydraulic clutch master cylinder is also the brake master cylinder,they both use the same one
How do you disconnect the clutch line from the master cylinder on a 1996 Chevy pickup?
sledge hammer last I knew the master cylinder was for the brakes, but the above answer may be adequate for that question.
What is wrong if there is no resistance in the clutch pedal for 1996 Mitsubishi Galant with manual transmission?
it means you have no clutch fluid(brake fluid) or that you possibly have a leak in the line somewhere or that it needs to be bled.might possibly be the master or slave cylinder.first check the clutch fluid resivor.if its empty then you need to top it off and bleed the line @ the master cylinder then at the slave cylinder.then find out why you have no fluid...the clutch fluid resivor is the smaller one of the two,check inside the car for a leak too,follow the clutch pedal to the firewall and you will see the small rod that goes into your clutch master cylinder,if you have a leak there the master cylinder is bad
Where is the clutch fluid reservoir for 1996 Toyota Tacoma?
It is located on the firewall between the brake master cylinder and the wheel well. It should be have a round black cap on top. It is about three by an inch and ahalf. Do not confuse this with the brake master cylinder.
How do you know if the clutch cable has gone in a Ford Escort 1996?
They don't have clutch cables. It is a hydraulic clutch with a master cylinder and a slave cylinder. If the clutch won't work fill the brake master cylinder with fluid. The clutch uses the same fluid as the brake and they share the same resrvoir of fluid. Follow the line from the clutch master cylinder across the transmission to the slave cylinder of the clutch. The slave cylinder is on the front middle of the transmission/engine. Take the cover off the bleeder valve and place a clear plastic hose over the nipple into a container of brake fluid. Have someone pump the clutch several times and then hold it to the floor. This is the time for you to open the bleeder valve. Air will escape into the container of fluid. Once the bubbles have stopped close the bleeder valve and have your assistant pump the clutch again. Keep doing this procedure until there are no more bubbles. Fill the master cylinder with brake fluid while you are doing this. If it goes down to far it will get air into your brakes and your clutch.
Where is the clutch slave cylinder located on Chevy 1996 Z24 cavalier?
It should be very close to the clutch bellhousing itself. Follow the hydraulic line from the clutch master cylinder down. I hope this helps you. it's actually inside the tranny between the motor and tranny good luck .....chevy boy
Why you get a good motor put in your 1996 geo tracker and the transmission does not take the gears?
Have your hydraulic clutch fluid checked to make sure it is not low. The clutch master cylinder is located on the drivers side high-rear.
Where is fuel filter located on 1996 Mazda protege?
The Fuel filter is located on the firewall, next to the brake master cylinder and right behind and below the carb.
Is the 1996 Mazda B3000 hydraulic clutch self adjusting?
No this clutch needs to be bench bled prior to instalation.
How many miles can you get out of a 4-cylinder motor out of a 1998 626 Mazda?
I have 182 k on my 1996 4-cylinder Mazda 626
