Cars & Vehicles
Pontiac Sunfire
Ford Explorer Sport
Ford Explorer Sport Trac

How do you fix the light switch that has the cruise control and turn signal switch on a 1997 Pontiac Sunfire SE?

161718

Top Answer
User Avatar
Wiki User
2015-07-15 21:21:01
2015-07-15 21:21:01

You've got to disable the airbag and remove it, then pull the steering wheel, .... go to www.autozone .com for more detailed instructions. hope that helps. Ron

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

If memory serves, there isn't one. All that switching is done at the turn signal/low highbeam/cruise control stalk.

User Avatar

It's the the turn signal switch that controls the Cruise Control Assembly. Therefore any problem to the Turn Signal switch affects the whole road safety.

User Avatar

There is no relay. The flasher in under the dash on the left of the steering column

User Avatar

To use the cruise control on the PT Cruiser, turn the cruise control on in the steering wheel. Accelerate to the desired speed and push in the end of the left turn signal knob. The cruise control should then control the speed. To take the car out of cruise control, a person can tap the brake.

User Avatar

under dash drivers side mounted above the brake pedal

User Avatar

The turn signal switch is located on the left side of the steering column just behind the steering wheel. It also controls Headlights, Hi/Lo beam and cruise control.

User Avatar

Low beam bulb burnt out? Replace bulb. Bulbs OK? If the dimmer switch is also the turn signal/cruise/headlight on and off switch, you probably have to replace the entire switch.

User Avatar

Remove the panel under steering wheel. There will be 2 flashers. Replace one on right.

User Avatar

on the turn signal lever it is a small slide switch

User Avatar

I imagine that your '96 is the same as mine, and that the cruise control ON/OFF and SET switches are on the end of the turn signal/headlight switch. On or the other of those switches may be bad, or the connection to the switches has come loose. In either case, you will need to remove the shroud around the steering column to gain access to the headlight/turn signal/cruise switch. If you end up replacing it, it comes out with only one screw, but take note of how the wiring harnesses are routed and be sure to re-route them the same wayor you'll have a heck of a time getting the switch seated properly when you put the new one in.

User Avatar

take the wheel well out first then reach in and turn bulb socket

User Avatar

Turn on the hazard switch (emergency blinkers). You should hear it under the dashboard on the drivers side. The emergency blinker and turn signal are each controlled by a different relay but the relays look alike. Once you've located the emergency blinker relay, the turn signal relay is nearby.

User Avatar

camshaft sensor - signal low could be that or check the wiring to it. Other possibilities MAF or TPS

User Avatar

It may be a safety feature on your car. If you are going to make a turn you for sure do not want the cruise to be engaged.

User Avatar

The combination turn signal, cruise control, windshield wiper, and headlight dimmer switch simply plugs in. Pull the relay switch out and replace with the new switch.

User Avatar

Pull off panel under steering wheel. You will see two separate flashers. Replace the one on the right.

User Avatar

Probably either in the "convenience center", located at the driver's side kick panel, or inside the steering column housing.

User Avatar

goto: http://www.autozone.com/az/cds/en_us/0900823d/80/19/24/46/0900823d80192446/repairInfoPages.htm for diagram of location

User Avatar

The 1985 S10 Blazer GMAC รŠoffers a delay wiper on the black cruise control lever. รŠThe part number is AM-64109149.

User Avatar

I think they call that the "control module" or equvilent. Usually, if you ask for a wiper, turn signal or cruise module, you'll get the one that controls all three.

User Avatar

My Haynes manual says that the "96 turn signal/hazard flasher is plugged into the "convenience center" which is mounted at the top of the left kick panel. FriPilot

User Avatar

Pulling the turn signal switch toward you should switch the lights to the low beams. If that doesn't work, you may have to replace the switch, which means replacing the entire turn signal stalk.

User Avatar

how do you remove the turn signal assembly on a 1989 Pontiac Bonneville


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.