answersLogoWhite

0


Best Answer

find the fan belt, make sure the car is OFF, then take a regular bar of soap and rub it on the underside of fan belt. That will stop it from squealing. Worked for me!

look if is a car or sedan have to be a transversal engine and dont have fan belt if has only one belt they call it serpentine belt and is too old got to go replace it if it has two belts one for alternator and ac compressor and one for Power Steering that means the one for the alternator is loose and can be tight the noise is too loud with the heater on because the alternator is working extra and the belt is slipping

User Avatar

Wiki User

โˆ™ 2011-12-01 07:44:59
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you get rid off a loud noise coming from the fan belt on 2000 Mazda Protege SE 16L when the engine is still cold and you turn the heater on?
Write your answer...
Submit
Related questions

Why does your heater not work in a 94 Mazda Protege?

If your heater does not work on your 94 Mazda Protege, check the thermostat. You can also check the heater fuse to ensure it has not blown.


Where's the block heater on a 1992 Mazda Protege?

My 92 Protege didn't have a block heater, I had to get one installed.


Where is the block heater in a 2003 Mazda Protege?

Right Rear of engine block. Above Alternator, Below coolant drain plug


Show you where is ignition coils on Mazda protege 2003?

On top of the engine..Two black blocks that have wires coming out of it


Where is the block heater on a 1999 Mazda Protege?

i think it does nt have one


Can a Mazda protege engine fit in a Mazda protege5?

yes, protege 5 is 01-03 yr you can fit the protege same years for i direct swap and if you want an older engine youll nee the ecu and matching harness.


What is the head bolt torque for 1.6 Mazda protege?

whar are the torque specs for head bolt on a 1999 Mazda protege 1.6 engine


Where is the fuel reset button on the Mazda Protege?

The Mazda Protege fuel reset button can be found on the firewall in the engine compartment. The reset button will be in the middle of the firewall.


Where is the heater core located on a 2000 Mazda protege?

Behind the Glove Box.


Can you take a 2000 Mazda protege LX engine out and put it into a 2000 Mazda protege ES?

yes all the dx lx and es proteges have the same engine. atleast that year does


Is a 1999 Mazda Protege 1.8 liter engine an interference engine meaning if the timing belt breaks will the pistons hit the valves?

No , the 1.8 liter 4 cylinder in a 1999 Mazda Protege is not an interference engine


Where are there pictures of a 2001 Mazda Protege engine?

at the library


Where is the ECM on your 2000 Mazda Protege?

The ECM on the 2000 Mazda Protege is located on the backside of the engine. It is half way up above the drive shaft.


Why would the heater core be hot going in but cold coming out on a 1993 Mazda Protege?

Most likely a plugged core. You can try flushing it, but you may end up replacing it.


Is a Mazda Protege 2001 2.0 liter an interference engine?

No , it is not an interference engine


Where is the starter on a 1994 Mazda Protege?

The starter, on a 1994 Mazda Protege, is located on the driver's side of the engine. It is just behind and to the right of the oil fill cap.


Where you can get a diagram of a 2000 Mazda Protege LX engine Thanks?

A diagram of a 2000 Mazda Protege engine is available through service repair manuals. The manuals are available in either print or PDF form.


How do you bypass the heater core on a 91 Mazda Protege?

Remove both heater hoses from inlet & outlet of heater core. Connect these hoses together.


What type of oil 2001 Mazda Protege?

A 2001 Mazda Protege uses standard 10w-30 motor oil. This provides a good balance of viscosity and protection for the engine.


Why does the engine light keep coming on indicating code PO401 in a 2000 Mazda protege?

Trouble code P0401 means:Exhaust gas recirculation-insufficient flow detected


Where is the transmission dipstick located on a 1997 Mazda Protege?

It is the center to the right of the engine...


What type of engine oil does a 2003 Mazda Protege 5 take?

5w20


What is the check engine code PO660 for a 2001 Mazda Protege?

Click the link.


Can you pull the engine out of a 2000 Mazda Protege from the top?

Yes, you can if the trans is disconnected.


How do you change heater core on 93 Mazda protoge?

Replacement of the heater core on a 1993 Mazda Protege is going to first require the removal of the entire dashboard. Once that is removed then the heater control box will need to be removed and disassembled in order to get access to the heater core inside.