0
How do you get to spark plug number 3 on a 2002 Ford Ranger 4.0 engine to remove it?
Wiki User
∙ 13y ago
I've read about some people safely supporting the passenger front and after
removing the front tire , pulling the rubber liner down and going through the
wheelwell
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you replace spark plug wires on a 3300 oldmobile engine?
To replace spark plug wires on a 3300 Oldsmobile engine, open the hood and remove the wires from the end of the engine. The number of spark plug wires most often corresponds to the number of cylinders your engine has.
Where is number one spark plug on 1997 Ford Ranger?
V6 engine in Ford Ranger firewall 3 - 6 2 - 5 1 - 4 front
Spark plug gap for 1983 Ford Ranger 2.8liter engine?
The spark plug gap for a 1983 Ford Ranger 2.8L is .044"
How do you change 2004 Ford Ranger 4.0 L spark plugs Specifically No 3.?
you have to remove tire on that side and work below the top part of engine
What is the spark plug sequence for a 2002 ford ranger?
For what engine ? 3.0
2003 Ford Ranger Spark plug type?
The spark plug number that is in my 2003 Ford Ranger XLT is: AGSF34FP - Motorcraft.
Spark plug gap for 2000 Ford Ranger 3o engine?
.042 to .046 inch (according to the 2000 Ford Ranger owners manual ) spark plug gap for the 3.0 L - V6 engine
Where are the spark plugs located on a 2004 Hyundai Sonata 24L 4 cylinder engine?
To locate and change the the (4) spark plugs on a 2004 Hyundai 2.4L 4 cylinder engine: Remove the (4) 12mm bolts from the decorative plasitc engine cover. Remove plastic cover from engine and place it off to the side out of your way. Standing in front of the car, the (4) spark plugs are located laterally (left to right) in the recessed area underneath where the plastic engine cover was removed. Note: This engine has (2) coils....They are located above spark plugs number (2) and (3) from left to right. Starting with the fist spark plug on the left: Remove the spark plug cable by pulling straight up on the insullated connector. Using a spark plug socket, remove the old spark plug and install a new one in it's place. To access the second spark plug from the left, remove the electrical connector and the spark plug cable wire from coil number (1) and then remove the (2) 12mm bolts that secure the coil to the engine. Spark plug number (2) is located directly under the coil. Lift the coil straight up removing the insulated connector from spark plug number (2). Using a spark plug socket, remove old spark and install a new one in it's place. Repeat same procedures for spark plugs number (3) and (4).
What spark plug for 1999 ranger 6-cylinder 3.0 engine?
On a 1999 Ford Ranger : Check the Vehicle Emissions Control Information ( VECI ) decal in the front of the engine compartment , it will show what type of spark plugs to use , and the spark plug gap
What is the spark plug gap for a 88 ford ranger?
The spark plug gap for the 2.3 litre 88 ranger is .035. This information can be found on the decal inside the engine compartment.
2005 Hyundai Sonata Where are the spark plugs located?
You didn't specify whether you have the (4) cylinder or the (6) cylinder engine..... I have a 2004 Hyundai Sonata 2.4L 4 cylinder and I just changed the spark plugs in it. I believe that the 2005 2.4L engine is the same. To locate and change the (4) spark plugs on a 2004 Hyundai 2.4L 4 cylinder engine: Remove the (4) 12mm bolts from the decorative plastic engine cover. Remove plastic cover from engine and place it off to the side out of your way. Standing in front of the car, the (4) spark plugs are located laterally (left to right) in the recessed area underneath where the plastic engine cover was removed. Note: This engine has (2) coils....They are located above spark plugs number (2) and (3) from left to right. Starting with the fist spark plug on the left: Remove the spark plug cable by pulling straight up on the insulated connector. Using a spark plug socket, remove the old spark plug and install a new one in it's place. To access the second spark plug from the left, remove the electrical connector and the spark plug cable wire from coil number (1) and then remove the (2) 12mm bolts that secure the coil to the engine. Spark plug number (2) is located directly under the coil. Lift the coil straight up removing the insulated connector from spark plug number (2). Using a spark plug socket, remove old spark and install a new one in it's place. Repeat same procedures for spark plugs number (3) and (4). Note: If you have the (6) cylinder engine, the front (3) sparks pluge are readilly accessible but in order to access the (3) rear spark plugs, you will have to remove the intake manifold.
What is the spark plug gap on 96 Ford Ranger XL 2.3 engine?
On a 1996 Ford Ranger : Check the Vehicle Emissions Control Information ( VECI ) decal located in the front of your engine compartment ( it will show the type of spark plugs to use and the spark plug gap )
