0
How do you install a splice kit to the existing wiring harness of a 2002 Dodge Dakota if the blower motor resistor overheated and welded itself to the existing wiring harness?
Wiki User
∙ 14y ago
Don't know about a splice kit but this is how I do wiring problems & may save you a few bucks. Go to a junk yard (Auto salavge yard) & get the wiring-connecter from a Dakota (a Ram may have the same connecter). Get as much of the wires as you can. On your truck go back beyond the melted part & find the wires to the relay. Make sure the wires match. say it is orange with a white stripe etc, Use a crimping tool & cut that wire Trim off insulation about 3/8 inch put on a wire splice & crimp with tool. Take same color wire from new wires & crimp it to other end of wire crimp. Check the rest of the wires for melted areas. All you are doing is going around the damage spot & replacing it.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
1995 Nissan Sentra blower motor resistor installation?
Locate the resistor under the dash attached on the blower motor housing. Disconnect the wire harness connector. Remove the resistor and install a new one.
How do you install a trailer wiring plug on a 1996 Chevy blazer?
Check with your local auto parts store, they can sell you a trailer harness that simply plugs into your existing harness, very easy to do, just follow instructions. The harness should be in the $25 range.
How do you replace your blower motor resistor on a 2003 Chevy Trailblazer?
The resistor is located under the hood, on the firewall, passengers side. Unplug the wire harness from it, remove the small screws holding it in place, remove it from the housing. Reverse procedure for install.
Install blower motor resistor town and country 95?
I just replaced my blower motor resistor in a 95 town and country. pretty easy its located on the fire wall passenger side. Facing the van, open the hood its top left almost under the hood hinge with the harness plugged into it. pull off the harness and the two screw bolts replace and your done.
How do you install a heater blower resistor in a 2004 jeep rubicon?
You need to remove the glovebox. Its located in the dash under the glovebox. It is held in place by 2 screws and a harness. Remove the harness and screws and pull out and down from underneath the dash. Put the new one in in the opposite order.
How do you install a wiring harness for trailer lights on a 2004 Chevy silverado?
you can buy a wireing harness that just plugs into your existing wires at a parts store, you do not have to cut any wires! just unplug back by your bumper and plug in the new plug. that's it.
How do you install a resistor in a 2009 Kia Sedona?
You can install a resistor in a 2009 Kia Sedona, first locate the heater box under your dash, remove the two screws, and replace with a new resistor.
How do you install the resister?
The pins of a resistor are interchangeable.
Can you install a 2010 dodge ram radio in a 1999 dodge ram with existing wire harness?
It would not be worth the time to do it. With the existing harness, no. The 2010 radio was built with can bus technology. It communicates with other parts of the truck like computer, air bags, etc. I'm sure there is a way around it, but would take WAY too much work.
How do you install fog lights on a 2005 Honda Civic EX Is factory wiring already existing?
The wiring is not there. You need to install the harness. Buy a shop manual. I bought aftermarket fog lamps that came with install instructions but it's too complex to write up here. Try a google search
Where is the wire harness for lights while towing a boat on a 2003 Chevy tracker?
I took mine in to Uhaul to have them install a tow bar and light harness. Mine didn't come with a light harness, they had to install one.
How to replace blower resistor in 2002 olds intrigue?
A blower resistor can be replaced, in your 2002 Oldsmobile, by removing the resistor wiring. Remove the retaining screws. Reverse the process to install the new resistor.
