you have to remove the back driver trim in the back of the Jeep..........you will find a green plug, the aftermarket wiring will plug into that.......................good luck
Just get a wiring harness form e-trailer for about $30 it is easy to install has instructions with it. Wayne
If it doesn't have a trailer plug, it does not have a factory trailer harness.
The trailer wiring kit is available from Jeep at about $125 and plugs into a wiring connector accessible through a panel in the left rear (inside) fender panel (behind the spare tire, near the left rear turn signal) with the trailer wiring harness routed through a grommet in the bottom of the compartment
Not all trucks are built with a trailer harness plug. If you can not find one, then your truck does not have one and you need to install one.
you do not need the extra 7 pin if your not running electri brakes
2006 Dodge Dakota - Where do i find the trailer wiring harness
Have you looked under the vehicle? I'd be surprised if the wiring harness wasn't already there and taped up under the vehicle. Barring that, most business that sell and install trailer hitches will also install trailer wiring harnesses. If you're a DIY, go to the local auto parts store and ask. They probably have the wiring harness you need all setup to plug into the manufacturer's wiring harness.
You can find a trailer wiring harness for a Chevrolet in a Haynes repair manual. The manuals are available at most auto parts stores.
Your local auto parts store can sell you a trailer wire harness for that vehicle that simply plugs in to the original harness and it is weather tight. It installs in minutes.
Check with your local auto parts store, they can sell you a trailer harness that simply plugs into your existing harness, very easy to do, just follow instructions. The harness should be in the $25 range.
U-Haul sells a kit with instructions
Your best bet would be to call or go to your local auto parts store and tell them you need a "plug in" trailer wiring harness for your vehicle....these are very nice items and easy to install, as you just "plug" them into your exsisting vehicle's wiring harness. No need to "search out" for which wire goes where and no splicing of the wires either. They are more expensive than a "standard" wiring plug, but the "extra" cost is more than worth the "time" and headaches you will save!
very easy .I bought my wires on eBay ,,,the trailer harness plugs right into your lights no cutting at all
I have a 1997 JEEP CHEROKEE sport 4.0. How to wiring for a heavy duty trailer brake switch ?
Trailer wiring harness part #118382 - any local Auto Parts Store should care this.
The easiest way is to buy and install a plug in wiring harness available at most parts store.
The easiest and best thing to do is to buy the harness that just fits into the factory wiring. It's avaible at most parts stores and it isn't expensive. That way you don't have to cut and splice.
Purchase a harness that is custom made for your vehicle and is not a universal harness. It comes with complete instructions on how to hook it up. It is very easy and normally no wiring is needed. It is just disconnect and plug in. Here is just one, and you may find one cheaper at Walmart or local dealers. http://hitches4less.com/jeep-grand-cherokee-trailer-wiring1.html
under the car,behind spare tire,is the wiring harness with access plug for dodge trailer harness (optional) my came with 2012 journey
The factory wiring harness for the trailers will plug in under the back of the vehicle in the area of the spare tire, the harness plugs into the wiring harness for the tail lights.
Subarus all have a connector for a trailer wiring harness built in. There is a supplemental trailer harness that you purchase from your hitch supplier and it just plugs right in. Instructions are available on-line. This one is for a 2001, but they have been the same for a number of years.
You can use the factory approved method with a $125.00 wiring part. Another possibility is the $25.00 part at any auto store the wiring converter , but this may interfere with the computer system in the chreokee. It's you choise here is a link for more info http://www.wjjeeps.com/trailer.htm#WIRING
If it is like a 99, just remove the plastic panel behind the spare tire on the drivers side in the back. In one of the cut-outs you will see connector plugs that connect the harness to the tail lights. Good luck. go behind the spare tire, there is a panel that has to be removed. You will see some black connectors in there. You can by a wiring harrness that will plug into there without any cutting of the factory wiring harness. These work fantasic, as I have one in my 2001 Cherokee. this is very easy to do has the new harness plugs right into the vehicles. You can find this wiring harness at Walmart or any parts store it is made by Hoppe. Good luck and I hope I helped you. Semper Fi
when you buy the harness to wire in, the intructions for correct wiring will be on the harness packaging