If it is like the '97 SC2, which it likely is:
Remove the plastic cover from around the steering column.
Turn the old ignition cylinder to ACC (I know what you are about to say... If you can turn the cylinder, why replace it. Unfortunately I can't answer that. I had to drill out the old lock to replace the one on my saturn. Please consult a locksmith before doing so. You don't want to drill into the wrong parts.)
With the old cylinder turned to ACC, there is a small button on the side (probably upper right towards the air vents) Push this button in and the old cylinder should pull out. Installation is reverse of removal (without the drilling...)
Ignition Lock? or Door Lock?
Remove the retaining ring, from the top of your 1997 Ford Astro ignition lock cylinder. Remove the wiring harness from the back of the ignition lock cylinder.
Remove the retaining ring at the top of your Chevy S 10 ignition lock cylinder. Slide the ignition lock cylinder out. Remove the wiring harness from the back of the ignition lock cylinder. Reverse the process to install the new ignition lock cylinder.
Begin by removing the retaining ring at the top of your 1994 Ford ignition lock cylinder. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the ignition lock cylinder. Reverse the process to install your new ignition lock cylinder.
Begin by removing the retaining ring at the top of your 1996 Chevrolet Silverado ignition lock cylinder. Slide the ignition lock out and remove the wiring harness. Reverse the process to install your new ignition lock cylinder.
Attach the wiring harness to the end of the ignition lock cylinder. Slide the ignition lock cylinder into the slot. Tighten the retaining ring at the top of the cylinder.
Disabling the keyless ignition security lock on a 2007 Saturn can be done by programming the security locks. Turn the ignition to run, without actually starting the engine, and press the unlock switch for eight seconds.
It engages and disengages the lock that starts the vehicle. There are 2 parts to the switch. The ignition switch and the lock assembly.
You will need to attach the wiring harness to the end of your 1984 Chevrolet Blazer ignition lock cylinder. Slide the cylinder into the cylinder slot. Secure the ignition lock cylinder with the retaining ring.
Begin by removing the retaining ring at the top of your 1996 Mercury Tracer ignition switch. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the cylinder. Reverse the process to install your new ignition lock cylinder.
Assuming you are sitting in the car with the key in the ignition you just push the door lock button on the drivers door, all the doors should then lock.
I have changed an ignition in one. I used a pneumatic cut-off wheel to cut straight slots in the blank faces of the two bolts that retain the lock cylinder. Then, I used an impact screwdriver to remove the bolts. when you get the new ignition lock cylinder, you can use a large flat screwdriver to re-install the bolts.
On the column accross from the key lock cylinder
You could check with a locksmith to find out if it is repairable. If it were mine I would install a new lock cylinder
I don't know about the blue and gray plastic things, but the ignition lock cylinder must have the key in the on (run) position in order to get it to release in order to remove it, and the same on (run) position to install the lock cylinder.
Yes, 4 wheel ABS was available on all Saturns in 1997.
go to a repair shop they'll tell you
The only way to remove the lock is with a key, you will need to get a locksmith to make a key to the old ignition so you can install the new lock set. Forcing the lock forward will damage the column and could be very expensive to replace.
The wheel should lock when you take the key out of the ignition. If it doesn't, there's something wrong.
If it is on the steering column you have to remove the steering wheel, lock ring and turn signal plate to access the ignition lock bolt. There are a couple of tools needed to do this. work.
Should be correct
To replace Ignition Switch, first you have to remove the old one. To do this you disconnect battery ground cable. Remove the upper steering column shroud by removing the five self-tapping screws. Remove tilt steering column lock lever, Remove lower steering column shroud, disconnect the ignition switch electrical connector, turn ignition switch lock cylinder to the "run" position, remove the two screws retaining ignition switch, and finally unhook the ignition switch from the actuator. Now to install the new one.Make sure that the ignition switch lock cylinder is in the "run" position. You can test for the "run" position by rotating the ignition switch lock cylinder approximately 90 degrees from the "lock" position. Hook up the ignition switch into the actuator. You might have to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes. Install retaining screws. Connect electrical connector to ignition switch. Connect battery ground cable. Check ignition switch for proper operation, including start and accessory positions. Also, make certain that the column is in the "locked" position. Then Install upper steering column shroud. Install the lower steering column shroud and tilt steering column lock lever.
1996 rodeo- how to remove key from lock ignition?