0
If its the same as a 1993 model its on the sterring column right above where the pedals are and a bear to get to.. there are 2 screws make sure you disconnect the battery.
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
What are the release dates for Disneyland - 1954 Double Switch 31-15?
Disneyland - 1954 Double Switch 31-15 was released on: USA: 25 January 1987
What are the ratings and certificates for Disneyland - 1954 Double Switch 31-15?
Disneyland - 1954 Double Switch 31-15 is rated/received certificates of: Australia:G Iceland:L
What are the release dates for The Open Switch - 1926?
The Open Switch - 1926 was released on: USA: 31 December 1926
What are the release dates for Martin Kane Private Eye - 1949 Subway Switch 4-31?
Martin Kane Private Eye - 1949 Subway Switch 4-31 was released on: USA: 11 June 1953
What are the ignition point gap settings for a 1972 Chevrolet 350 engine?
the dwell is 29 to 31 degrees and the gap is .019.
Can you get a performance chip for a 92 camaro rs 31 V6 and if so where?
try hypertech.com i believe your prom chip in the cpu can be changed stage 1 2 or 3
How many hours are there in October?
There are 31 days in October. 24 hrs a day The switch to winter time adds one hour 24 * 31 +1 =745
2002 jaguar x type- your interior windows fog up in cold weather?
WORKSHOP PROCEDURE1. Open door.2. Turn ignition 'ON'.3. Operate front seat fully rearward for access.4. The air recirculation switch should be in the fresh air mode.5. Turn ignition 'OFF'.6. Remove the glove compartment hinge retaining screws (Illustration 1).7. Remove the glove compartment retaining screws (Illustration 2).8. Disconnect the glove compartment lamp electrical connector (Illustration 3).9. Remove the glove compartment.10. Disconnect the air inlet blend door actuator electrical connector, undo and remove the climate control upper front stepper motor securing screws and displace the climate control stepper motor and reposition to gain working access (Illustration 4).11. Remove the air inlet blend door actuator securing screws (Illustration 5).12. Displace and remove actuator.13. On all vehicles, align the actuator shaft as follows: Connect the air inlet blend door actuator to the electrical connector, and switch the ignition 'ON'. By a combination of operating the air recirculation button ON/OFF and disconnecting the electrical connector at the correct time set the shaft to the correct position. The flat opposite the curved face should be set nearest to and parallel with the line on the actuator bodyNote: A DTC will be stored during the alignment procedure since the open circuit will be detected.14. Turn ignition 'OFF'.15. Ensure the air inlet blend door is in the fresh air position.Caution: Care must be taken not to apply too much adhesive as this could be pushed backwards on the motor housing when inserted in the climate control unit.16. Apply Super Glue Gel or a suitable locally sourced adhesive to the actuator shaft (Illustration 7).Note: Do NOT apply adhesive to the end of the actuator shaft.17. Align, install, and fully seat the actuator. Hold the actuator in position until the adhesive has set.Note: Do NOT switch the ignition 'ON', or operate the air recirculation switch until ten minutes have elapsed to allow the adhesive to set.18. Install and tighten actuator-securing screws.19. Connect actuator electrical connector.20. Reposition and install the climate control upper front stepper motor.21. Install and tighten the climate control upper front stepper motor securing screws.22. Install the glove compartment.23. Connect the glove compartment lamp electrical connector.24. Install and tighten the glove compartment retaining screws.25. Install and tighten the glove compartment hinge retaining screws.26. Turn ignition 'ON'.27. Operate front seat to original position.28. Turn ignition 'OFF'.29. Position WDS alongside vehicle, switch 'ON' Portable Test Unit (PTU) and allow software to load.Note: During previous operation, Connect PTU to vehicle via diagnostic cable.30. Clear DTCs, switch OFF PTU, disconnect and return WDS to original location.31. Close door.
Lumina apv Fuel pump test?
Check pressure At idle 13-20 psi With ignition on and not running 23-31 psi
What are the release dates for Whale Wars - 2008 Bait and Switch 2-8?
Whale Wars - 2008 Bait and Switch 2-8 was released on: USA: 31 July 2009
How do you install a fuelpump on a 92 31 liter Chevy Lumina?
It is located in the fuel tank. Unless there is an access panel in the trunk or under the rear seat, the tank must be removed in order to install the pump.
What is the fuel pump pressure for a 1991 Pontiac firefly 3 cylinder?
engine off and ignition on: 23 to 31 psi engine at idle: 13 to 20 psi
