I know you have to remove the dash to get to it. I'm looking for an answer on how to remove the dash because I have the same problem. The dash does not have to be removed, at least on my 2001 Sentra. You do have to remove the glove box (two latches inside of the box have to be pulled inward to release the glove box) then there is a cover that has to be removed (two Phillips head screws). These will be exposed when the glove box is removed. Pull the cover down slightly, reach in above the cover to release two white clips. Now comes the hard part. Laying on your back, looking up under the dash, next to the firewall and close to center of the car is a four wire cable that attaches to the resistor block. The block is held in place with two more Phillips head screws. One screw is visible, one is behind the connector. (Trust me, it's there.) The resistor block assembly will pull down out of its slot. Unclip the resistor block, take it to the Nissan dealer and say "Give me one of these." Mine cost $25. Attach the new block to the connector, slide it back in place and replace the two mounting screws. Slide the cover into the two retaining clips then replace the two screws. Put the glove box back into place the push the retaining latches into place. It takes only about two minutes to remove the block and the same to replace it. The new resistor block may look different but the important thing is the connector not the shape or color of the block. You can continue to operate the fan on high while the resistor block is out of its connector. It only controls fan speeds 1, 2, and 3.
Locate the resistor under the dash attached on the blower motor housing. Disconnect the wire harness connector. Remove the resistor and install a new one.
AnswerWhere can i find a diagram to locate where the starter is on a 1993 Nissan Sentra automatic
To replace the headlight bulb in a 1994 Nissan Sentra first prop the hood of the car. Locate the headlights and remove the bulbs from the housing. Install the new bulbs.
To change the blower motor resistor in a 2002 Nissan Maxima, locate the blower motor resistor under the glove compartment on the passenger side of the vehicle. There is a clip that is depressed and then the resistor will slide out. Remove both ends of the resistor and then replace with the new resistor.
Simply locate the starter, and it's a remove and replace operation. A couple of bolts, a couple of wires and your back in business.
To remove a 1998 Nissan Sentra Transmission, you first need to locate all of the bolts. From there, you will remove the bolts. Undo any wiring or tubing that goes into the transmission. From there, it can be taken out.
Inside gas thank. Remove back seat to see access panel.
You can install a resistor in a 2009 Kia Sedona, first locate the heater box under your dash, remove the two screws, and replace with a new resistor.
# Locate the blower resistor under the right-side of the instrument panel # Disconnect the electrical connector from the blower motor resistor # Remove the blower motor resistor mounting screws and remove the resistor from the housing # Installation is the reverse of removal
To replace the taillights on a 2001 Nissan front first prop the hatch open. Locate the rear lights plastic housing and remove them to find the bulbs. Replace the bulbs.
There is a thing called the resistor box that drops the voltage through the switch leaving the full voltage to run on number 4 of the switch. Locate this resistor and replace, this should fix problem.hope this helps
Locate the resistor under the hood near the blower motor on passenger side firewall. Unplug the electrical connector. Remove the screws holding the resistor in place. Remove the resistor. Install in reverse order.
Bottom left of dash under steering wheel locate sunglass holder, open holder and then pull up fusebox underneath
You might try to locate them by following the 4 wires coming out of the distributor. There should be a spark plug on the other end of each of them.
1995 Nissan Sentra Fuses: Your owner's manual is the best place to locate your fuse box(es) and identify your fuses. Don't rule out that your issue is being caused by a bad bulb too - so check fuses and bulbs. See sources and related links below for bulb information.
To replace the rear brake lights on a Nissan Primera first open the trunk lid. Locate the tail lights and find the plastic cover which hide the bulbs. Remove the cover and then the bulb. Replace with a new bulb.
First locate the resistor, it should be under the hood, on the firewall, passenger side, near the blower motor. Unplug the electrical connection, remove the small screws holding it in place then wiggle the resistor out.
To replace the thermostat on a 1987 Nissan pickup, drain the radiator. Locate the thermostat which is under the top hose assembly, and remove the screws holding it in place. Put the new one in position and refill the radiator.
To replace the thermostat on a 2002 Nissan Altima first drain out the coolant. Then proceed the to locate the thermostat housing which is by the engine compartment fuse box. Unbolt the housing and replace the thermostat.
Open your hood and locate the upper radiator hose coming from the top of your radiator. this hose should go straight to the thermostat housing. You will need to drain the radiator and remove the hose. there should be three ten millimeter bolts hold it on remove the bolts and replace thermostat.
To add refrigerant to your vehicle you must first locate the low side port to your ac system. There is a great web site www.idqusa.com that can help you locate the low side port on most vehicles along with helpfull information about a vehicle ac system.
The 2002 Nissan Sentra blower motor resistor is located near the blower motor itself, wich can be found under the dashboard, on the passenger side of the car.To access it, you have to remove the glove compartment and the isolation panel that covers the bottom of the blower. Do the following steps:# first, locate and open the glove compartment on the passenger side; # remove the four upper screws and slide the doorlock bracket out; # pull out the two pins at the inner bottom corners of the compartment; # take out the glove compartment assembly; # remove the two screws retaining the isolation panel and slide the later out. Looking under the dashboard, you can now see the blower motor and, on its left side, near the firewall, the resistor block brown connector.To take out the blower motor resistor:# remove the white plastic bracket that faces it; # unplug the brown connector; # remove the two screws on the resistor's socket; # pull the resistor block out. The resistor block is actually a PCB ("Printed Circuit Board"). The traces printed on this board have different electrical resistance, and are used by the control assembly to vary the speed of the blower fan.
Open the hood and locate the resistor module just above and to the right of the passenger shock strut tower. It will pull right out. The resistors may be fine, but the wires or connectors may be shot. Replace as necessary.
If it looks the same as the European Sunny the resistor is located on the (right hand drive) passanger side. Under the dashboard (or under the glove box) the blower is located. The resistor is located in the blower housing (so the heat is blown away). The resistor is connected by a 4 pin long connector. Pull this one out and unscrew the 2 screws that are located near the 4pin. Then you can get the whole (creditcard) resistor out. Replacing the resistor in Holland costs about 60 euros, but in the us the come around $15.
i want to do it my self