== All transmitters that are to be recognized by the remote control door lock receiver (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode, all previously programmed transmitters will be erased upon receipt of the programming signal from the first transmitter. Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. The order in which the transmitters are programmed is important. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. Use care to program the transmitters correctly. The scan tool must stay connected until all of the transmitters are programmed. # Install a scan tool. # Turn ON the ignition with the engine OFF. # With the scan tool, select Body, go to Remote Function Actuation. # Select Special Functions. # Select Program Key Fobs. # Select the number of key fobs to be programmed. # Press and hold the LOCK and the UNLOCK buttons simultaneously on the first transmitter for approximately 15 seconds. The power locks should cycle to confirm programming of the first fob is complete. # If you are programming more than one transmitter, repeat the previous step to program up to 4 transmitters. # Remove the scan tool. # Exit the vehicle. Attempt to lock/unlock the doors to verify the programming. # Operate the transmitter functions in order to verify correct system operation. == All transmitters that are to be recognized by the remote control door lock receiver (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode, all previously programmed transmitters will be erased upon receipt of the programming signal from the first transmitter. Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. The order in which the transmitters are programmed is important. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. Use care to program the transmitters correctly. The scan tool must stay connected until all of the transmitters are programmed. # Install a scan tool. # Turn ON the ignition with the engine OFF. # With the scan tool, select Body, go to Remote Function Actuation. # Select Special Functions. # Select Program Key Fobs. # Select the number of key fobs to be programmed. # Press and hold the LOCK and the UNLOCK buttons simultaneously on the first transmitter for approximately 15 seconds. The power locks should cycle to confirm programming of the first fob is complete. # If you are programming more than one transmitter, repeat the previous step to program up to 4 transmitters. # Remove the scan tool. # Exit the vehicle. Attempt to lock/unlock the doors to verify the programming. # Operate the transmitter functions in order to verify correct system operation.
The are two batteries in the key fob.
it has to be done by the dealer. =(
You have to have it done at the dealership.
AnswerGo to thhis website: www.mygmlink.com/pdf/go2content/manual/us/en/pontiac/1999grand prix.pdf. This is the website for the ownre's manual.
Dealer only on 96+ newer Jeep Grand Cherokee's
I have a jeep 1994 Jeep Grand Cherokee and found this answer on this site under programing a 1995 jeep Grand Cherokee. Its a very good description uses the same FOB.
Dealer only on 96+ newer Jeep Grand Cherokee's
I may not be right but try holding down your lock button until the doors lock?
I am trying to find out how to do the reprogramming, but haven't found out how, but did find out that from 1999- 2004 the door lock fobs are interchangeable. You may need to take to Jeep dealer to actually get it programmed, but at least you won't have to buy a new fob.
How do you program a key fob to a 2003 Chevy Malibu
To program any kind of key fob you have to take it to a dealership.
Have you replaced the battery in the fob?