1)Purchase new bumper cover wing (wrap around) mounting rails and hardware 2) Open trunk and remove liner left and right to gain access to mounting hardware 3) Remove taillight harness left and right 4) Remove taillights (left and right) These are sealed and will require very careful prying away from body. Work slowly and allow the adhesive to release. 5)Completely remove the bumper cover push locks (2) beneath each taillight 6) Examine inner fender (inside trunk) for (2) bumper cover wing mounting bolts on left and right sides. Loosen but do not remove (inner bolt on passenger side is behind the jack assembly). Apply penetrating oil as necessary to loosen. NOTE: these bolts are often rusted badly and WILL break. Hence the need to purchase new mounting rails before starting work. 7) Carefully pry rear side marker assemblies from vehicle and remove wiring harness. Pry carefully from the rear. 8) Remove (2) mounting bolts beneath left and right bumper cover wings (fender) may be rusted and require vise grips and some force to pull out. 9) Remove (1) mounting behind each rear wheel (upper end of bumper cover wing) 10) Remove bumper cover corner bolts below and toward the outside corner of left and right taillight 11) Carefully remove the bumper cover wing bolts previously loosened inside the fender. Don't worry if they break, you have new hardware. 12) Carefully pull bumper cover toward the rear to free it from the vehicle. 13) Installation is the reverse of this procedure.
Remove the screws in the wheel wells and underneath the plastic cover to remove the bumper cover. Then you can see to remove the actual bumper.
how to remove front bumper 2002 Impala
To change the trunk light in a 2002 Nissan Maxima, a person will need to unscrew the cover over the light. Then they can remove the old bulb and replace with a new one. Then screw the lens cover back on.
1. If needed raise vehicle and support it on Jack stands 2. Remove the retaining screws in the wheel wells and along the upper and lower edges of the bumper cover. Remove the tail light housings. Remove the rear trim plate and pull luggage compartment trim out for access then remove the remaining bumper cover retaining screws. Remove the bumper bolts 3. On station wagons remove the rear window washer fluid reservoir for access to the bumper retaining bolts. The remaining bumper bolts are accessible from below 4. Pull the bumper and cover assembly out and away from the car
I just did this last night on mine. There is a plastic cover on the top of the bumper. You have to remove that to get to the bolts underneath it. Its a real pain to remove it without breaking that plastic cover you have to crawl underneath it and squeeze the plastic clips together one at a time. After you remove that, you can remove the bolts under it. There are more in other places, but I forget where, I'd have to go look again.
Yes. The rear bumper cover was the same on the Infiniti G20 from 1999-2002.
2001-2002 I know the screws are behind the trunk panel. Two on each side I think and the ones in the back.
First you need to remove the bumper. For that you need to remove bumper cover moldings. Once you remove those you will see two bolts (12mm) that you will need to remove. After you remove them, you need to remove two (T25) screws that are located under cover fender one on each side towards the end of bumpers. To do that you need to unscrew each of them about 1/2" each and then push back in. After that, you need to remove 6 plastic clips that are located on top of the bumper. They are removed by pressing the button that is in the center of each clip. Now to remove the bumper just pull it towards yourself. Once you will do that you will figure out what to do next in order to take off the headlamps.
YOU NEED T TAKE OUT TRIM ON TOP OF RADIATOR AND HAVE LONG FINGERS TO REMOVE OR U CAMN TAKE BUMPER COVER OF AND REMOVE HEADLIGHT TO GET IT
See below- Pretty much the same thing for all 2002-2008 Civics.
where is the IAT Sensor on tne 2002 maxima
Yes with some slight modifications. You will have to trim the bumper support and remove the foam padding. You will also have to switch the fender liners bc the 2002 liners wont reach the 2004 bumper.
is if the bumper or the bumper skin (cover) the bumper will fit the skin wont due to slightly different shaped headlights BUT its just a tiny bit of cutting to get it to work
The 2002 Nissan Maxima has a V6 engine.
The 2002 Nissan Maxima has 24 valves.
How do i remove the pdc on x5 bmw bumper
There is a site that shows how to remove the rear bumper in an Accord but it is NOT the 2002 but the 2003 model. I don't know how much different this would be but it might give soe insight. The link is www.cardomain.com/ride/650229/3
Remove front cowl On the drivers side there is a steel bumper support you must remove to loosen half the bumper The tritip will extend beyond the wheelwhell...remove it. your done! Replace in reverse order
To replace the front bumper cover and the front reinforcement(along with painting and installing it) a dealer will charge you about $850
To remove the cover box to get to the fuel injector on the 2002 Envoy, first remove the intake manifold and the valve cover. You can do this by loosening the four bolts that hold the intake manifold first.Ê
Factory service manuals that have been scanned and converted to Adobe Acrobat files are available for just a few dollars on eBay. Although I cannot tell you that I have seen the instructions to remove the bumper cover in these manuals they have the most complete instructions available since the original paper manual is put out by Subaru.
The 2002 Nissan Maxima has a 4-speed automatic.
The 2002 Nissan Maxima is a gas-powered vehicle.
were is the fuel pump located in 2002 nissan maxima
The 2002 Nissan Maxima has double overhead cam (DOHC).