0
How do you get the axle out to change the boots on the cv joints
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Is there a clip on a 1999 grand Cherokee rear axle?
No, the rear axle shaft does not have an internal retainer clip. You remove the four nuts on the inside of the brake backing plate and remove the axle shaft with a slide hammer and hub adapter.
How do you change the wheel bearing hub on 1999 4x4 jeep grand Cherokee Laredo?
Remove the wheel. Push the brake caliper piston back with a prybar or heavy screwdriver to make clearance to remove the caliper. Remove the entire caliper assembly by removing the 2 large bolts with an 18 mm socket and breaker bar.(they are tight!). Remove the rotor. Remove the 4 nuts on the axle retaining ring located behind backing plate using a 9/16" wrench. Attach a slide hammer to the wheel studs on the axle and hammer the axle out. Put the axle in an arbor press and press the bearings off of the axle. Press new bearings, seal and collar back onto the axle. Reassemble the rotor, caliper, etc. This can be done at home if you have access to a slide hammer and arbor press and some basic hand tools. The requestor was asking about the rear wheel bearing, as am I. There is no disk brake caliper on the rear wheel..... Do you have drum brakes then? If you email me at mudislife2@yahoo.com ill get more information on the jeep and see if i can help you better. In the step where he said "Put the axle in an arbor press and press..." That line has omitted some steps. After axle is removed from axle tube, remove the 4 studs from the axle bearing retainer. There is a soft steel retainer ring that must be removed before the bearing can be removed. The soft steel retainer is removed by drilling a 3/8" hole into the ring (don't drill into the axle... stop short of the axle) and splitting the ring off the axle with a cold chisel (this is stated in the service manual.) Once the retainer ring is off, install bearing splitter press tool between bearing and flange, then place the axle into a press, with blocks under the bearing splitter press tool (KD tools 2264, or OTC 1183). Press and remove bearing and seal from axle. To reassemble, you'll need a pressing ring will press on the inner race only of the bearing. First, put the retainer back onto the axle, then slide the seal onto the axle, cavity side to the inboard end of axle, then slide bearing onto axle, then press bushing. Support press bushing on press arbor plates, axle into arbor flange end up, and press axle flange until bearing is seated. Then slide new retainer ring onto axle, and press that on similar to bearing. Pack the new bearing with fresh grease, then install 4 studs into retainer plate, and reinstall assy into axle tube.
Does a 1995 jeep Cherokee 5.2 limited have a front LSD?
The front axle did not have limited slip from the factory.
How do you remove hub bearing on 1996 jeep Cherokee sport 4.0L?
You would need to remove the brake caliper, brake caliper bracket and also the brake rotor. The cotter pin and nut that holds the axle in place also needs to be removed, and then the axle needs to be tapped out of the hub with a socket. Then you can get at the three bolts that hold the hub into place. An instructional video of this procedure has been listed below to help.
Will the front axle off a 97 Grand Cherokee fit a 99?
nono
How do you remove the front axle on 1998 Honda 450 foreman?
How do you remove the front axle on 1998 Honda 450 foreman?Read more: How_do_you_remove_the_front_axle_on_1998_Honda_450_foreman
How do you remove the front axles on a 1993 Honda Civic?
Begin by removing the tire and wheel from your 1993 Honda Civic. Remove the brake assembly and the brake rotor. Remove the axle retaining bolts. The axle will come off.
Can you remove oil pan on 2004 Dakota with 5.9 v8?
Yes, if you remove the front axle first.Yes, if you remove the front axle first.
How do you remove front axle from a Pontiac grand prix?
Remove the front tires, from your Pontiac Grand Prix. Remove the brakes and rotors. Unbolt the axle from the suspension. Remove the axle.
How do you remove front tire off a Honda big red 1984?
Take the crown nut off the front axle and bang the axle back out, be careful not to damage threads. They are usually hard to get out, it may require heat on the axle. Good luck
How do you remove front axle on a 1994 Thunderbird?
Thunderbirds never had a front axle
How do you remove a Honda xr250 front wheel?
Lift bike up off of ground. Remove front brake pads. Remove speedometer gear box screw and pull out cable. Loosen 4 small bolts on axle shaft holder. Loosen axle shaft. Remove axle shaft, 4 small bolts and holder. Wheel will come off.
How do you change the front axle on a 1998 Honda civic?
jack up car remove wheel remove axle nut take bottom 19mm bolt loose and 14mm loose from horseshoe remove horseshoe separate spindle from lower ''a'' arm pull Axle out of spindle remove from trans to replace reverse process
Is it required to break the transmission loose from the engine to drop the oil pan on a 4.7L 2002 Dodge Ram 1500 engine?
Either remove the trans, or remove the front axle on a 4x4.Either remove the trans, or remove the front axle on a 4x4.
Do you need to separate the steering knuckle in order to remove brake rotor on a 1997 Honda Accord?
no, remove the caliper and the caliper mountaing bracket, if it is on the front you may have to remove the axle not but there is no need to remove any steering part
What is the axle nut torque on a 2000 Honda Prelude?
front- 36mm
How do you replace front wheel bearing Honda odyessy?
Jack up the Odyessy. Remove the wheel and the brake caliper. Take the brake rotor off. Remove the axle nut cover, and the cotter pin. Remove the axle housing. Replace the inner and outer bearings as well as the races.
