We need you to answer this question!
If you know the answer to this question, please register to join our limited beta program and start the conversation right now!
How do you remove the ignition switch on a 1989 Chevy Corvette?
Remove the retaining ring from the top of your 1989 Chevy Corvette ignition switch. Slide the ignition switch out and remove the wiring harness. ...
Asked in Chevy Blazer S-10
How do you change the ignition switch on a 1989 Chevy Blazer S10?
You will need to remove the retaining ring from the top of your 1989 Chevrolet blazer ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch. ...
Asked in Car Starting Problems, DIY Projects
How do you replace a 1989 Mercedes Benz 300sel ignition?
Retaining ring from the top of your 1989 Mercedes-Benz ignition switch. Slide the ignition switch out. Remove the wiring harness. Reverse the process to install your new ignition switch. ...
How can i replace an ignition switch in a 1989 Oldsmobile cutlas ciera sl?
Remove the retaining ring from the top of the ignition switch. Pull the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch. ...
Asked in Chevy 350
Trying to find key in ignition buzzer location in a 1989 Chevy Blazer?
The buzzer that lets you know the key is in the ignition in a 1989 Chevy Blazer is in the steering column. To access it you would need to remove the steering wheel with a special tool, or remove the ignition assembly. The key makes contact with a tab that activates the buzzer. ...
How do you change the ignition lock cylinder in a 1989 Chevy Cheyenne when there is a key broke off in the ignition and it won't turn?
A locksmith may be able to remove the broke key and make a new one. Or just replace the ignition. ...
How do you remove an ignition rotor on a 1989 gmc s15?
If you do not see 2 screws holding it in place it just pulls off.
How do you remove-replace a 1989 Vanagon ignition switch?
Here is a link to an illustrated step-by-step procedure for replacting a Vanagon ignition switch: http://carboncow.net/vanagon/projects/ignition_switch.htm ...
Asked in GMC Sierra
Where is the ignition module located in a 1989 GMC 1500 Sierra 5.7L V8?
The ignition module on a 1989 5.7 liter is located in the distributor. Remove the cap, then the rotor, and you will be looking at the module. The module is held in place with two screws. Real simple. Good luck, David ...
Asked in Jeep
How do you replace the ignition switch on a 1989 Jeep Waggoner?
you have to remove the steering wheel and the turn signal. this requires special tools that can be purchased or rented cheaply. ...
Asked in Chevy Trucks and SUVs, Chevy G20
How do you install ignition switch on 1989 Chevy G 10 van?
how do you install new ignition switch on 1989 chevy G10 van?
Asked in Ford Ranger XL
Where is the ignition module located on a 1989 ford ranger?
The 1989 Ford Ranger pickup truck ignition module is located on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall. ...
Asked in Ford Aerostar, Chevy Astro, Ford Aerostar XL
How do you remove the ignition switch on a 1989 Ford Aerostar van?
If you talking about were the key goes into the Ignition then try this. I have a 1991 aerostar. Disconnect your battery. Then remove the screws holding the plastic steering wheel cover. then by looking at the bottom of the steering wheel near the ignition you should see a little button (or what looks like a hole) With the key in the ignition push this button/hole and pull on the ignition (not Majorly hard) Slowly turn the key and it should...
Asked in Mazda Trucks
Where is the ignition module located on a 1989 Mazda b2200?
where is the ignition module located on a 1988 Mazda b2200
Asked in Chevy Celebrity
Where is the ignition module on a 1989 Chevy Celebrity?
On a 2.8l v6 it is at the front of the engine behind the ignition coils.
Asked in Mercury Tracer
Where is located the ignition module in a mercury tracer 1989?
ignition control module is located under the distributor cap
How do you install an ignition module for 1989 beretta?
First disconnect the negative battery cable then make sure engine is cool before you do the next step, disconnect the cooling fan then remove then remove the four bolts that hold the fan in, remove the upper radiator support mount, jack the car up, make sure you put it on jack stand, there is a bolt on the bottom of the ignition module mount, you have to remove that from under the car, then remove spark plug wire make sure you...
Asked in Mercury Cougar
How can you start a 1989 mercury cougar with a broken ignition switch?
how can you start a '89 mercury cougar with a broken ignition switch?
How do you replace the starter in a 1989 Chevrolet Celebrity?
how do you repace the Ignition Module
Asked in Acura Integra
How do you set the ignition timing on a 1989 Acura Integra?
Ignition timing is set on a 1989 Acura Integra by setting the distributor to the appropriate angle. When set at the factory recommended angle the car will turn over with no problems. ...
How do you install an ignition switch on a 1989 Chevy truck 2500?
Hi there. i own a 1989 Chevy cheyane and had to fix my tilt steering. the same applies to removing the steering wheel and etc to get to the ignition switch as well. i went to Canadian tire or parts dealer. i had to rent a steering wheel puller etc. remove steering wheel cap, undo main bolt. remove plastic horn cover ( watch out for springs) remove tilt arm. then you have to remove torx screws from base of tilt housing. slide off...