0
How do you remove and install a throttle position sensor on the throttle body of a 1991 Acura Integra?
Wiki User
∙ 17y ago
If you are able to all you need is a set of good pliers, and try really hadr to grip the two ends and turn the rivet out. All you need is like 1 or 2 turns then you can take over wiht you hand. Afterwards it would be really helpfull to go to the harware stor and buy little srews that match so you dont have to do it again. I'm pretty sure you have to drill out the two OEM rivets that attaches the TPS to the TB. Use pop rivets to reattach.
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
How do you install a throttle position sensor on a 1998 mercury villager?
remove and reinstall
How do you install a throttle position sensor on a 99 F150?
Disconnect the battery. On the side of the throttle body, disconnect the wiring from the position sensor. Remove the bolts from the sensor, and lift the sensor off, reverse the procedure to install the new one.
How do you replace the throttle position sensor in a 98 Olds intrigue?
The 1998 Oldsmobile Intrigue throttle position sensor is held in place with two retaining screws. Remove the retaining screws and the wiring harness. Reverse the process to install the new throttle position sensor.
How do you replace a throttle position sensor of a 2003 Chevrolet suburban?
It is located on throttle body, opposite side of where throttle cable is located- Unplug it, remove any screws or bolts holding it on then install new part in reverse order.
How do you change bearings on a Acura Integra?
Bearings require a mechanical press to be properly changed in an Acura Integra. Remove the hub from the vehicle and take it to a press. The machine will properly install a new bearing and ensure a safe install.
Where is the Throttle Position Sensor on a 1990 Ford Bronco?
it is located in the throttle body. On the bottem. You need to remove the air filter hoses, remove the 4 bolts to the throttle body and then 2 screws to remove the tps.
How do you install throttle position sensor in 1996 Toyota Camry?
There are two bolts and a wiring harness connector that need to be removed. Remove the connector first ,then the bolts. Install new one and re-assemble. Pretty easy to do and easily accessible.
How do you replace the tps in 1990 Chevy Celebrity?
To remove the throttle position sensor: 1. Unplug the electrical harness. 2. Remove the bolt that holds the tps in place. 3. Remove the tps. To install a new tps reverse the removal procedure. There is no adjustment given.
How do you change a starter on a 1993 Acura Integra?
To change a starter from a 1993 Acura Integra remove the mounting bolts that connect it to the transmission. Then unplug the solenoid from the wire harness. Install the new unit.
Where is the throttle position sensor 1994 ford e150 58?
It is located on the bottom of the throttle body. You can find the throttle body by following the two big air pipes from the air filter box, they end at the throttle body. To access the throttle position censor you must remove the throttle body.
How do you replace the throttle position sensor in 94 ford e150 van 5.0?
Disconnect battery negative. You have to take off your throttle and cruise control cables from the top of your throttle body. Then unplug your idle motor and TP sensor. Then take and remove and mark all your vacuum hoses from the throttle body. Remove the 4 bolts holding the throttle body to the plenium. Unbolt the TPS and install in reverse. Get a new throttle body gasket in case you old one rips but I would use a new one anyway.
How do you remove the governor on a Acura Integra?
You can remove the governor on an acura integra by having the ecu chipped.
