0
first disconnect the battery. *note (if your car is equipped with the delco loc 2 audio system be sure to deactivate this first before disconnecting battery)if it allready is not active disconnect battery cables you will need an 8mm wrench for that. next locate starter under the vehicle on the lower front side of the motor. remove the wiring from the starter this will require a 13mm wrench and an 8mm wrench.place wiring to the side noting where each of the wires go *note hold wiring near the connections so you don't break the terminals on the wires allthough easy to fix it is a pain in the but to do so.now you will need to remove bracket at front of starter this takes a 13mm wrench for the bolt to the block and a 10mm at the front of the starteryou may only have to loosen bolt at the block and remove the nut from the starter and bracket should be able to be swung to the side. now take a 15mm socket and ratchet with small exstension bar. remove final 2 bolts that mount the starter to the block.again note if a shim plate is used between the block and starter because you will need to put this back in when the new starter is installed.will cause starter hangups and wreck your flywheel if it is not. install new starter with shimplate if it applys to your vehicle.do not tighten bolts until all bolts and brackets have been lined up and started. than tighten bolts. install wiring making sure you got them in there right spots than reconnect battery.and anything else you may have had to remove. front engine splash guard etc.tahat should do it good luck and i hope this helped.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you install a starter on a 1993 Chevy Corsica?
Begin by removing the positive cable from your 1993 Chevy Corsica battery. Remove the cables on the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.
How do you remove a starter in 1998 Chevy Malibu?
HOW TO REPLACE A STARTER ON A 1998 CHEVY MALIBU
Do you have to remove the Upper Intake Manifold to replace the fuel pressure regulator on a 1996 Chevy Corsica V6 3.1L?
Correction: It is a 1995 Chevy Corsica. Not a 1996.
How do you replace side view mirror on a 1995 Chevy Corsica?
The side view mirror on a 1995 Chevy Corsica is mounted by screws. Remove the screws and panel for the mirror on the inside of the vehicle. Pull and replace the unit.
How do you replace the water pump on a 1990 Chevy Corsica 2.2L?
Where is the Water Pump located and how do you replace it on a 1990 Chevy Corsica?
How do you replace a starter on a 1988 Chevy astro van?
Remove the positive cable from your 1988 Chevy Astro battery. Remove the cables from the front of your starter. Remove the starter retaining bolts. Reverse the process to install the new starter.
How do you replace the starter in a 92' Chevy Lumina Z34?
Remove the positive cable from your 1992 Chevy Lumina battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.
How do you replace the alternator on a 1989 Chevy Corsica?
Begin by removing the alternator belt on your 1989 Chevy Corsica. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install the new alternator.
How do you replace the starter on a 92 Chevy Lumina euro?
remove bolts and replace it how do u think
How do you replace the starter on a 1993 Chevy Cheyenne?
Remove the positive battery cable from your 1993 Chevy Cheyenne battery. Remove the two cables from the front of the starter. Remove the three starter retaining bolts. Reverse the process to install the new starter.
How do you replace a starter on 2003 Chevy Cavalier?
Disconnect the positive cable from your 2003 Chevy Cavalier battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install the new starter.
How do you replace ignition switch for a 1994 Chevy Corsica?
Remove the retaining ring at the top of your 1994 Chevy Corsica ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.
