answersLogoWhite
Mitsubishi Mirage
Ford Expedition
Ford Expedition Eddie Bauer
Ford Expedition XLT

How do you remove and replace the PVC valve on a 1997 Mitsubishi Mirage?

343536

Top Answer
User Avatar
Wiki User
2011-09-13 06:14:46
2011-09-13 06:14:46

The PVC valve is located on the driver side rear part of the valve cover. It is screwed into the cover with a black hose coming from it. You just need a wrench to un screw it. Don't cross thread the new one going back in. Thread in by hand to start.

1

Related Questions

User Avatar

What is the correct valves calibration on mitshubishi mirage 1996 1.5L

User Avatar

On the intake manifold, back dirver side.

User Avatar

On the 1997 Mitsubishi Mirage 1.5 liter, the EGR is located on the side of the intake manifold. You'll probably have to remove the air intake tube that goes to the throttle so you'll have enough room to reach it.

User Avatar

There is not a distributor on a Mitsubishi Mirage. It uses two coils that are located on top of the valve cover. one coil provides spark for two cylinders.

User Avatar

The timing belt on a Mitsubishi Mirage connects the camshafts with the crankshaft. This ensures that each valve is opened at precisely the right time based on the rotation of the engine.

User Avatar

Right next to where you put in the oil (Gasket Cover)

User Avatar

Expansion valve is located on the A/C Evaporator Core. Most of the times you have to remove the whole dash to reach it/ replace it. Good luck.

User Avatar

how do you replace the valve cover gasket on a 2002 mitubishi lancer

User Avatar

Take it to a shop. Probably not worth it if you waited too long, so u might need a new motor unless your going to tear it down

User Avatar

The EGR valve, on your 2005 Mitsubishi, is located beneath the air cleaner. Remove the air cleaner housing. The valve should be visible and labeled.

User Avatar

Your kidding me right; replace the valve.

User Avatar

To replace the valve lifters on a Cavalier, remove the intake manifold, valve covers and rocker arms. Remove the heads of the lifters using needle-nose pliers.

User Avatar

valve clearance should be pusted under tune up spec under "stock hood" sticker should be on the left hand side

User Avatar

The Mirage could have a leaking valve cover. Wash the engine off at a car wash, then keep a careful check to see where the oil is coming from, then you will know what needs to be replaced.

User Avatar

Remove the bottom hose from the evaporater at the firewall, pull out the expansion valve, i highly recommend flushing out the system to remove excess sludge. Replace the valve and the hose.

User Avatar

The PCV valve on a 1995 Buick Park Avenue is located on the top of the valve cover. Twist the valve and pull to remove and replace it.

User Avatar

Remove the heater control valve and replace it.

User Avatar

No you do not! th egr valve is located just under the throttle body. there are 2 10mm bolts holding it in, you just need to remove air intake to the throttle body! it is directly under it!

User Avatar

By isolating the valve then remove it and replace it

User Avatar

To change PVC valve on a 1993 Nissan 300zx, first remove the oil dip stick and remove the tension clip from the PVC valve hose. Then remove the hose and the old PVC valve. Replace with a new PVC valve.

User Avatar

The best way to fix an expansion valve for the A/C system is to replace it. of course then you have to evacuate and recharge with freon.

User Avatar

Replace the heater control valve motor, a dealer part, costs around $166.00.ish

User Avatar

http://thecommi.angelfire.com/index.html I have included a picture of the EGR valve on my website. scroll down and click on EGR valve. the valve is easy to replace. remove the wireing connector from the top, remove the two 10mm mounting bolts from its base. pull strait up and off. should take under 10 min to replace. http://thecommi.angelfire.com/index.html I have included a picture of the EGR valve on my website. scroll down and click on EGR valve. the valve is easy to replace. remove the wireing connector from the top, remove the two 10mm mounting bolts from its base. pull strait up and off. should take under 10 min to replace.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.