Headlights Tail and Brake Lights
Chevy Corvette
Dodge Ram
Ford Expedition Eddie Bauer

How do you remove and replace the light switch on a 1977 corvette?

343536

Top Answer
User Avatar
Wiki User
2006-03-19 23:21:00
2006-03-19 23:21:00

You need to take the screws out of the lower dash panel next to the drivers side door and across the top. Then find a steel button on the bottom of the switch. When you push the button pull out the knob you use to turn the lights on. The knob should come all the way out. Then turn the outer screw out that holds the switch onto the dash board. The switch should come off. Then unplug it from the wires on the back.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

You need a star point screwdriver. Remove the 2 screws pull out light assembly. Remove the light socket from housing and replace bulb. replace in reverse order. 5 minutes.

User Avatar

Take the screws out of the lenses, remove the lense and replace the bulb.

User Avatar

Brake light switch is located on the brake pedal arm. Unbolt & bolt in new one. Wiring will unplug & plug back in to new switch.

User Avatar

how would remove brake light switch and replace on an 88 gmc

User Avatar

brake light switch is mounted by the brake pedel remove lower panel above brake pedel and then you will see the switch should be able to turn the switch to replace

User Avatar

If you remove the plug from the switch and jump the plug with a paperclip and the lights come on, its your switch.

User Avatar

Remove license plate, dissconnect backup light wire, remove bolts to backup light, pull backup light sideways, reach hand to tail light, twist socket.

User Avatar

the flasher unit is built into the hazard light switch on dash you have to remove the small cover around switch unit & remove switch remove plug from back & replace whole unit

User Avatar

remove trim plate around switch,take out screws holding switch in,remove wires then replace in reverse order!!

User Avatar

Look under the dash on the 1996 suburban, and locate the brake light switch on the brake pedal arm. Remove the switch nut, and slide the switch out. Unplug the wires from the switch and install the new switch.

User Avatar

How do you replace a break light switch on 1995 Chevy Tahoe

User Avatar

If you need to replace your dome light switch you will need to remove the cover first. You can use your fingernails or even a small knife to get the cover off.

User Avatar

back side of the brake pedal

User Avatar

how to replace the brake light switch at the pedal of a 2001 ford zx2

User Avatar

replace head light switch on 93 ford explorer

User Avatar

Parking switch? Do you mean the parking light switch? If you do, The dash will pull loose on the left top and bottom just above the switch and below. From there you can see how the light switch comes out.

User Avatar

The combination neutral start and backup light switch is mounted inside the shifter housing. Remove the screws holding down the shifter housing and remove the switch. Adjust the switch by moving it on its mounts.

User Avatar

Grab ahold of the light switch under the dash you should feel on the side of the light switch a spring button. Push the button in poll the light switch knob out. Then you unscrew the nut that holds the switch in. Once you get the switch out play around with it so you can see how it works. That way it's a lot easier to install it. By the way disconnect the battery or your lights will stay on.

User Avatar

remove trim, remove clock, remove clock light harness, and remove and replace clock light bulbs

User Avatar

Try spraying the brake light switch with WD-40 first. If that doesn't fix the situation, then: . Remove the under-dash panel. . Locate the switch near the top of the brake pedal and disconnect the wiring harness. . Remove the switch retaining pin and the white nylon washer from the brake pedal pin, then slide the brake light switch and pushrod off far enough for the outer hole of the switch to clear the pin. . Slide the switch down to remove it.

User Avatar

http://www.6speedonline.com/forums/996-turbo-gt2/176814-diy-head-light-switch-remove-replace.html

User Avatar

have your landlord or a friend fix it if you dont know how to switch a light switch because there can be a promblem with the light and its very important that you be safe


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.