answersLogoWhite

0


Best Answer
Copy

What you have is called the lock plate for the steering wheel. Go to your favorite auto parts store and ask them for a lock plate hold down tool. It will be needed to depress the plate's spring, so the snap ring can be removed that is holding the lock plate onto the steering shaft.

User Avatar

Wiki User

โˆ™ 2015-07-15 19:47:49
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you remove the final piece from the steering column to remove the key switch and tumbler in a 1991 Oldsmobile Cutlass Supreme?
Write your answer...
Submit

Related Questions

Where is the ignition switch located on 1997 Oldsmobile bravada?

The ignition switch is located inside the steering coulum below the key and tumbler.


How do you remove the ignition switch tumbler on a 1986 dodge lancer 2.5?

Remove the screws on the side of the steering column. Remove the screws underneath the steering column and pull the bottom half of the column down. Slide a pin punch into the hole at the ignition tumbler assembly's bottom. Force the tumbler upwards and pull it out of the steering column.


Do you have to take the steering wheel off to change a ignition lock tumbler on a 96 Chevy Tahoe?

yes


How to change a key tumbler on a 1998 cadillac northstar?

When you say key tumbler, are you referring to thr ign key cylinder, door , glove box or trunk cylinder. All tricky, most difficult--steering col lock cylinder. Steering wheel, signal switch, must come off.


How do you replace ignition switch on 97 gmc jimmy?

Pull your steering colum apart along with steering wheel and dash plastic, ignition swith is next to the key tumbler. Swap the parts.


How do you change the ignition switch in a 1990 Pontiac Grand Prix without pulling the steering column?

the ign switch or the key & tumbler ???


What is the name of the ignition component in steering column of 1994 buick regal but not the key ignition switch?

The ignition switch. Where the key goes in is the key tumbler.


How do you remove key lock switch-from 2003 Buick century steering column?

On the GM cars I've worked on, you have to remove the steering wheel. There is a vertical retaining bold/pin that has to be remove to allow the tumbler/key lock cylindar. Remove the wheel. Remove the retaining pin. Then remove the tumbler. Reverse the above to install the new one. Hope that helps.


How do you use the word tumbler in a sentence?

Tumbler pigeons will be on display at our pigeon show next week. That's a 48-ounce tumbler of iced tea! That gymnast is a fantastic tumbler.


What is tumbler index of limestone?

how can do prepare the tumbler test in limestone


How do you change the ignition on a 1991 Oldsmobile Eighty - Eight?

You need to pull the steering wheel , puller helps .them remove the horn (note this is a no air bag car)the tumbler has a lock screw u should see it remove it and it pulls right out look it over good i put in a used one for a s 10 truck i had in the back good luck


How do you take the part out that the key goes into on a 1978 Chevrolet Malibu?

You are referring to the key and tumbler assembly. It requires special tools to remove the steering wheel and steering lock plate. It also requires a special tool for the installation. It would be cheaper to have a mechanic do it.


Why a tumbler is not made with a piece of cloth?

This is because generally use a tumbler to keep a liquid.A tumbler made of a piece of cloth can not be used to keep water.So, a tumbler is made with a material which has a property to hold the liquid.


Remove caravan ignition tumbler?

Remove the plastic 2 piece shroud around steering column so as to gain access to the housing the tumbler sits in. Find three Phillips screws to remove in holes in the lower piece. Turn the ignition key to the Run position. Insert a small tip screwdriver in the access hole on the bottom of the housing to push the spring-loaded tab which will free the tumbler so you can simply pull the tumbler out with the key. Installation is the reverse. Be sure tumbler with key inserted is set to the Run position. Depress spring-loaded tab, insert tumbler into housing hole with tab down. All the way in, turn key to the Lock (off position).


How do you unlock the ignition on a 1991 sel Mercedes 420?

the key must be in position #2 for the tumbler to be removed...if you lost the keys & have no key, the tumbler will have to be drilled out...also, the pins holding the housing into the steering column will have to be drilled out too..then you should be able to remove the entire assembly...of course, you're going to have to replace the entire assembly & tumbler...I'd try partsgeek.com for your replacement parts..reasonable prices & quick delivery..


How do you change key tumbler 89 eldorado?

Remove the inside door panel. Remove the linkage from the key tumbler. Remove the key tumbler retaining nut. Reverse the process to install the new key tumbler.


How do you replace the ignition tumbler for a 1999 dodge grand caravan?

Remove the plastic 2 piece shroud around steering column so as to gain access to the housing the tumbler sits in. Find three Phillips screws to remove in holes in the lower piece. Turn the ignition key to the Run position. Insert a small tip screwdriver in the access hole on the bottom of the housing to push the spring-loaded tab which will free the tumbler so you can simply pull the tumbler out with the key. Installation is the reverse. Be sure tumbler with key inserted is set to the Run position. Depress spring-loaded tab, insert tumbler into housing hole with tab down. All the way in, turn key to the Lock (off position).


What words come between tumbler and tuna?

what word is inbetween tumbler and tuna


How do you replace a key tumbler on a 1994 trooper key stuck in the tumbler and you cannot get it out car will not start?

This is an easy one. 1) remove battery cables 2) remove screws aroun steering column 3) try to start car one more time 4) buy a Haynes repair manual for the vehicle


How do you remove a ignition key tumbler in a 1977 Chevy pickup?

Remove the retaining ring from the top of your 1977 Chevrolet pickup truck ignition key tumbler. Slide the ignition key tumbler out. Remove the wiring harness from the end of the key tumbler.


How do you remove the ignition tumbler from a 1988 Chevrolet truck?

first you need a steering wheel puller .remove the center cap on the steering wheel then re move the nut i think its a 3/4 in nut after that there is a ring that has to be removed you will see it around the steering shaft you will need the tool that pushes the steel plate down any good parts person will know what you need i cant think of the name of it so after you get the plate off you'll see the turn signal switch there are 3 screws that hold it in place remove them and pull the switch out you can pull kinda hard on it to get out of the way once its out you will see a set screw were the tumbler goes in pull the set screw and the tumbler will slide right then just reverse the steps and your all done hope this helps


Would you replace both the Steering Lock Assembly and or just the ignition lock tumbler for a 1983 Mercedes 300 SD that you have to jiggle the steering wheel to get the key to turn in the ignition?

Replace just the steering lock unit. The tumblers are old, and they need to be replaces. After replacing the lock, go to a locksmith, and have him re-key the doors to match your new ignition lock.


What are the ratings and certificates for The Tumbler - 2008?

The Tumbler - 2008 is rated/received certificates of: Australia:R


How do tumbler door locks work?

Tumbler door locks work with the key being put in the lock and tumbler turning. This is one of the most common types of door locks.


How do you replace a ignition switch tumbler 1991 skylark?

how do you replace a ignitionswitch tumbler 1991 buick skylark