Brake Pads and Rotors
Ford Bronco
Ford Bronco II

How do you remove the front brake rotor from a 1989 Ford Bronco II?

888990

Top Answer
User Avatar
Wiki User
2015-07-15 19:19:50
2015-07-15 19:19:50

Hey April==You need to state wheather it is a 2 ot 4 wheel drive. If it is 2 wheel drive, simply remove the caliper first, then remove the spindle nut and pull the rotor off of the car with the hub. If it is a 4 wheel drive, I suggest you get a manual on your truck from Auto Zone for about $18 and it will give you pictures and everything. Goodluck, Joe

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Remove wheel. Remove brake caliper. Remove brake caliper mount. You can now remove the rotor.

User Avatar

Remove the tire and wheel from your 1995 Chevrolet K 3500. Remove the front brake assembly. Tap on the brake rotor with a hammer or mallet until it becomes loose. Slide the brake rotor off.

User Avatar

Remove the tire and wheel from your 1995 Chevy. Remove the brake assembly. Tap on the brake rotor with a mallet or hammer. The brake rotor will slide off.

User Avatar

Remove the wheel and tire assembly and the brake caliper then the brake rotor will slide right off.

User Avatar

The front brake rotor, on a 2004 Chevrolet Colorado, can be removed by first removing the wheel. Next, remove the brakes. The rotor will slide off

User Avatar

Jack up the front of your 1991 Mitsubishi Eclipse. Remove the brake pad assembly. Loosen the brake rotor by tapping on it with a hammer or mallet. Slide the brake rotor off. Reverse the process to install the new brake rotor.

User Avatar

Remove the tire and wheel. Remove the brake pads and break hardware. The brake rotor will slide off. You may need to tap the rotor with a hammer.

User Avatar

How do I remove the front rotors so I can replace the CV joints? .... After removing the brake pads and caliper assembly, of course.

User Avatar

There should be 2 screws on the front of the rotor, remove those and the rotor should come right off....you also have to take off the caliper bracket.

User Avatar

You remove the wheels, remove the brake caliper and the rotor is then free .

User Avatar

You didn't specify brake rotor or ignition rotor. If it's the brake rotor, remove the front wheel, remove the brake caliper, remove the bearing dust cap, remove the cotter pin, and then remove the castle nut, this will free up the rotor to be removed from the spindle. While it's off you may as well replace the wheel bearings. If its the ignotion rotor you simply remove the distributor cap, and then two screws hold the rotor on.

User Avatar

You usually have to take off the brake caliper, then the caliper mounting bracket to free the rotor.

User Avatar

2005 Toyota tacoma how to remove the brake rotor

User Avatar

Remove the brake caliper and hang it out of the way, then thread 2 8 mm bolts into the holes provided on the disk. Screw them in and the brake rotor will come off.

User Avatar

You will need to remove the tire and wheel from your 1995 Chevy Cheyenne. Remove the brake assembly. Tap on the rotor with a hammer or mallet. The brake rotor will slide off. Reverse the process to install the new brake rotor.

User Avatar

Remove wheel Remove caliper mounting bolts Slide caliper off rotor Rotor should slide off hub

User Avatar

Hello, Removing the front rotors on an Acura TL is clockwork. Here is a quick how-to guide: 1. Raise and safely support the vehicle. 2. Remove the front wheels. 3. Remove the brake hose mounting bracket. 4. Remove the brake caliper bracket mounting bolts, and remove the caliper assembly from the knuckle. 5. Remove the rotor retaining screws. 6. Remove the brake rotor by pulling it straight off the wheel mounting studs or if seized in place, remove the stubborn brake rotor by threading in two 8 x 1.25mm bolts, two turns at a time until the brake rotor is released. Good luck with your brake job!

User Avatar

Remove the front tires and wheels. Remove the brake assembly. Tap on each rotor disk to loosen them. Slide the rotor disk off. Reverse the process to install the new rotor disk.

User Avatar

Remove wheels Remove caliper mounting bolts Slide caliper off rotor Slide rotor off hub (if "peel off" type)

User Avatar

You remove the tire and wheel, then the brake caliper, followed by the caliper holding frame. Now the rotor will be free.

User Avatar

Have you had a front-end alignment? When you remove parts from the front end, you need to have this done.

User Avatar

It can be easy to change the brake rotors. Lift the car, remove the tire, brake shoe and rotor, put on the new rotor, replace the brake shoe, tire and lower the car.

User Avatar

first take off frontwheel then take off brake caliper then rotor will pull right off .

User Avatar

I believe that caliper is held with 10mm bolts. Remove caliper, then caliper mounting frame, then rotor will come off.

User Avatar

You remove the brake caliper frame and rotor is then loose.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.