answersLogoWhite

0


Best Answer

Buy a split boot from the parts store- that way you won't have to remove the shaft.

As long as you have the half shaft out, why not replace it since there is probably some damage to it from having a damaged boot?

User Avatar

Wiki User

โˆ™ 2015-07-15 21:22:38
This answer is:
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you remove the half axle on a 2000 Kia Sephia in order to replace the outer cv boot?
Write your answer...
Submit
Related questions

How do you replace outer tie rod end 1994 Buick?

In order to replace the outer tie rod end on 1994 Buick, you should start by loosening the jam nut, then unscrew the tie rod end and then remove the cotter pin. Fit it the new tie rod end and screw back all the parts.Ê


How to replace 2001 buick regal license plate bulb?

Open the trunk lid looking inside the trunk lid remove the 8 or9 plastic wingnut that hold the outer panel to the trunk, replace the lights and reinstall the panel in reverse order.


Where is the fuel pump located on a 1994 Saturn SL2 is it in the tank or in the line to the tank?

Its in the tank, as 99% of GM cars are. In order to replace you will have drop the tank, remove the outer safety ring, disconnect the wiring harness, and remove pump, pretty simple job if yo know what your doing.


How do you replace a headlamp for a 1994 Chevy G20 Van?

Remove the outer plastic trim to reveal the lamp frame holding screws. remove the frame and the lamp comes out the front


How do you replace front wheel bearing Honda odyessy?

Jack up the Odyessy. Remove the wheel and the brake caliper. Take the brake rotor off. Remove the axle nut cover, and the cotter pin. Remove the axle housing. Replace the inner and outer bearings as well as the races.


How do you replace inner tie rod ends on a 1992 Toyota Camry?

Remove wheel and disconnect outer tie rod from lower control arm. Clearly mark original position of outer tie rod end on shaft and remove outer tie rod end. Remove rack and pinion boot revealing. Unscrew inner tie rod from rack and pinion assembly.


Do you have to remove the shaft from the automatic transaxle in order to replace the outer CV boot on a 1990 Grand Am?

You do not have to remove it, but doing so will make the boot replacement a whole lot easier. Being able to clamp the axle in a vice is much nicer than trying to work around the front suspension pieces.


How do you Change Brake and Rotors on a 2004 Grand Prix?

Remove wheels Loosen 2 Caliper mounting bolts Remove only one to allow caliper to swing away from rotor Remove rotor Remove outer brake pad Use "C" Clamp to retract piston into caliper body Remove inner pad Replace inner and outer brake pads Replace rotor Resecure brake caliper BE SURE TO PUMP BRAKE PEDAL PRIOR TO MOVING VEHICLE TO SET PADS AGAINST ROTOR


How do you replace tie rods on 2000 neon?

There are two types of tie rods on a 2000 Dodge neon. The outer-tie rod connect to the inner-tie rods which mount to the steering rack. The outer units are threaded on to the inner- tie rods. Remove them by spinning it counter clockwise. Take a special tie rod socket to remove the inner-tie rod. Replace the units.


How do you replace indicator lens on a Volkswagen Passat 1.9TDI?

hi thereprise the mirror glass out and remove the outer casing and also remove the backing, there are 2 small screws at the bottom of the mirror remove them and replace the lens, dont worrie about which way you connect the mirror glass electrics as it is a curcuit,good luck


How do you replace air conditioning clutch on 2002 Oldsmobile Intrigue?

go to 99intrigue.shutterfly.com/compressor. Get clutch remover and installer. Get feeler gauge. Remove serpentine belt with 1/2" breaker bar. Measure air gap in clutch. Remove shaft nut. Remove clutch with remover. Remove outer snap ring. Remove pulley with pry bars or remover. Remove clutch coil with pry bars or remover. Replace new coil and pulley. Replace snap ring. Replace clutch, maintaining air gap. Reinstall nut. Reinstall belt.


How do you repair outer tierod end?

Remove old one and replace. Several specialty tools are required. The last step is a front end allignment.


How do you remove starter harley Davidson 1997 fatboy starter?

Disconect neg on battery, remove outer primary, remove jackshaft( keep parts in order when removing) remove rear tire, a motorcycle lift works good, disconect positive to starter, remove 2 1/4 inch allen bolts from starter, pull starter and catch spacer(notice direction of spacer it only goes back the way it came out.) Go to rear of swing arm pull starter from rear by the rubber fender guard. Replace in order the way it came out. It can be a pain but it's the only way I could replace mine.


How do you replace the inner tie rods on a 1999 Toyota Sienna?

It's actually very easy. Remove tires and loosen inner tie rods from outer tie rods completely keeping track of number of turns. Then remove cotter pin and nut from outer tie rod and remove. Unthread inner tie rod from steering assembly. They rent a tool at O'reily's which makes this much easier. Repeat these steps in reverse order to re-assemble. Immediatly get alignment performed.


How do you replace the outer tie rods on a Mitsubishi 3000GT?

Remove the tie rod nut. Pop tie rod out of the hole in spindle. Unscrew tie rod from steering box. Install new tie rod in reverse order. Have front end aligned.


How do ypu replace the outer tie rods for a Lexus gs300?

First, remove the wheels. Take off the cotter pin and the nut that connects the spindle to the tie rods. Hammer on the rod end until pops downward. Mark the alignment of the tie rod, remove it, and then replace it.Ê


How to replace a 1997 geo prizm lock?

If you mean the door lock cylinder...remove the interior door panel. On the back of the door handle there are 2 10mm hex bolts. To the outer edge of the door there is an access hole. With an extension, remove the 10mm bolt that holds the lock cylinder and door handle together. Reach in and push the nylon retainer that holds the rod into the cylinder (yellow on driver side, white on passenger side) and remove it. A slight twist of the cylinder will remove it from the door handle. Replace in reverse order.


How do you remove Nissan dualis door handle outer 2011?

How do you remove outer door handles on Nissan dualis


How do you replace clutch on a Yamaha ttr 125?

Remove the four bolts holding the clutch pressure springs, next remove the outer cover. ÊRemove the clutch pack and soak in oil, replace the cover with pack in position and use a new gasket put the cover back on and fill with oil.


CV boot Ford Ranger how to replace?

A CV boot is found on the axle of a vehicle. To replace the outer boot remove the axle bolt and pull the boot off. The inner boot requires removal of the whole axle.


How do you change the outside door handle on a 1990 D21 Nissan pickup truck?

you must pull inner door panel, window crank and inner handle then you have two 10 mm nuts holding outer door hanle on you must remove the release rod from handle remove nuts and replace handle assemble in reverse order


How do you replace the oil pump on a blazer 4 wheel drive?

The easiest way is go remove the front.differential u have to remove cv axles outer tierods and pitman and idel arm and front.drive shaft its tricky to get it out but not that hard


How do you replace a Brake tail light bar pacifica?

Open the liftgate and remove the upper tailgate liner. This will reveal 2 holes showing the nuts for the 2 inside screws. The outer ones are easily visible when you lift the gate. Remove all 4 nuts. Disconnect the electrical connector and the rear washer hose. Remove the spoiler and replace with new one.


How do you remove blade tool from army Swiss knife?

remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber remove outer casing then un screw the bolts, this will relese every single tool from the chamber


How do you remove the front outer door handle on a 2013 Ford Fusion?

how to remove front outer door handle on a 2013ford fusion