Starters and Ignition Systems
Nissan Altima
1995-2005 Chevy Cavaliers

How do you remove the ignition cylinder on a 1997 Nissan Altima?

151617

Top Answer
User Avatar
Wiki User
Answered
2008-04-01 22:58:18
2008-04-01 22:58:18

I just drilled out the security bolts on either side. Then it came off easy. Start with a small drill bit and get larger and larger.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


how to change a ignition switch on a nissan altima 2003

how to remove a alternator from a Nissan altima

How to remove the front bumper to a 1998 Nissan Altima?

Take the steering column housing off (usually held by 4 screws from the bottom) and remove the starter cap from the back of the ignition cylinder. In a Nissan, the ignition cylinder usually has a T shaped pin which turns the starter. if you can start your vehicle by turning the starter cap with a screw driver, you probably don't have an issue with the starter.

how to remove a power steering pulley on a 1997 Nissan altima

how to open dash on nissan Altima 2008

how to replace a heater core on a 2003 Nissan Altima 2.5

Remove the ignition cylinder retaining ring. Poll the ignition cylinder out. Remove the wiring harness from the back of the ignition cylinder.

You will need to remove the retaining ring at the top of your 2003 Kia ignition cylinder. The ignition cylinder will slide out. Remove the wiring harness from the back of the ignition cylinder.

u have to remove the rear deck lid, speakers r underneath how do you remove the rear deck lid on the 2005 Nissan altima

how do i remove the ignition switch in a 1995 Nissan quest

You will need to remove the retaining ring from the top of your 1975 Chevrolet pickup truck ignition cylinder. Slide the ignition cylinder out and remove the wiring harness. Reverse the process to install the new ignition cylinder.

Remove the retaining ring from the top of your 2000 Mercedes-Benz ignition lock cylinder. Slide the ignition lock cylinder out and remove the wiring harness.

Remove the retaining ring, from the top of your 1997 Ford Astro ignition lock cylinder. Remove the wiring harness from the back of the ignition lock cylinder.

just remove it and there you go it's out

Remove the retaining ring from the top of your 1997 Chevrolet 1500 ignition cylinder. Slide the ignition cylinder out and remove the wiring harness.

The stock stereo, from a 2003 Nissan Altima, can be removed by first removing the stereo front cover. Next, remove the four screws. Pull the stereo out and remove the wiring.

You can change the ignition cylinder on your 1999 Mercury Mystique by removing the retaining ring at the top of the ignition cylinder. The ignition cylinder will slide out. Remove the wiring harness.

Remove the retaining ring at the top of your Chevy S 10 ignition lock cylinder. Slide the ignition lock cylinder out. Remove the wiring harness from the back of the ignition lock cylinder. Reverse the process to install the new ignition lock cylinder.

Begin by removing the retaining ring at the top of your 1994 Ford ignition lock cylinder. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the ignition lock cylinder. Reverse the process to install your new ignition lock cylinder.

Remove the retaining ring at the top of your 1991 Acura Legend ignition switch. The ignition switch cylinder will slide out. Remove the wiring harness from the end of the ignition cylinder. Reverse the process to install your new ignition switch cylinder.

The 1994 Pontiac Grand Am ignition lock cylinder is held in place by the retaining ring at the top of the cylinder. Remove the retaining ring. Remove the wiring harness from the back of the cylinder.

To remove the ignition cylinder on a 2000 Lexus RX300, first remove the vanity engine cover by unscrewing it. Disconnect the wiring connector by pushing the clip that holds it in place. Finally, remove the bolts that hold the ignition cylinder.

you have to remove the door panel to access the inner door and remove the entire door handle assembly ( from the inside). Once you've got the handle out, remove the lock cylinder, to access the broken key.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.