answersLogoWhite

0


Best Answer

This is what I just did. First remove the 6 screws from both sides of the console. Next, remove the bottom rubber plate of the rear glove box of the console. It has a small grove that you can use a screw driver to pop it out. . Then remove the 2 screws you will see. Next, using a strong grip around the small grove (doesn't look like there is actually one there) , pull the rear cupholder/ashtray straight back. Inside you will see 2 bolts and 2 nuts holding the rear of the console to the floor. Remove them. Next, there is a wire plug you can see from the rear that goes up toward the passenger. This is for the front cigarette lighter on the console. Unplug it and remove the holder from the brace. This is the only wire disconnection. Next take the nut off of the emergency brake that pulls the cables, then raise the brake handle completely up. The console is now ready for removal, but first you must put the transmission in drive. Make sure the engine is OFF and the brake is set so it won't move. Lift up on the rear of the console (seems pretty high) and pull backwards. Pulling rearward pulls the 2 front pins out of their holders. Lift it out and you are done.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove the middle console bezel on a 2007 Sportage?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you remove the plastic bezel around the dash of 2000 Kia sportage?

my3mp


How do you remove the center console of a 2000 Nissan Altima?

pry up on the bezel around the shifter then remove 2 screws under bezel. remove 2 screws above radio faceing down remove ash tray remove radio bezel. move bolth seats up on the side of the ctr console is 2 screws remove then remove 2 screws in front of the shifter that are now showing after radio bezel is removed.remove screws located in cup holder crank up e brake and slide console out


How do you take out the center console on a 1997 Jeep Cherokee sport?

Pull shift lever handle straight up and off the lever. Use small screw driver to wedge out lever bezel, pull out bulb, remove bezel. You see there are 2 screws below you have to remove. Use small screw driver to wedge out 4wd handle bezel, pull out bulb, remove bezel. remove 2 screws at the bottom of the storage bin. You may have to pull 4wd shift all the way backwards. Console should then come out.


How do you replace a window switch for a 1978 corvette?

The best way to do it is to remove the whole center bezel (where the radio sits in) be very careful not to crack it. there are screws holding it in, you'll see them. If you have a radio installed, do what you have to do to get the bezel out. The vents on the top of the bezel are attached to it, so be carefull and work it out "SLOWLY". then remove the carpet panels, which are running from front to back on the side of the seats. there are 3 screws holding each one in. then remove the console bezel where the two window switches set into. you'll see the hex head nuts, two on each side (i believe) of the console bezel and two underneath where the radio bezel sat on. this should be enough to raise the console up and look underneeth the switches and you'll find them held in by two more hex head screws. reverse the installation. good luck!


How do you Remove 2008 ford explorer radio bezel?

You have to start by removing the top of the center console. Once this out of the way, the bezel will then unsnap from the dash. Use your fingers, tools will just get you into trouble. The bottom of the bezel is the hardest to remove because the floor console is partially in the way. Once you have all of the snaps undone, reaching behind the unit and unplugging the wiring connectors is a little tricky, but it can be done. I pulled the bezel off to install some switches. You can see the result by following the link below ResponderPSE


How do you remove the center console of a 2000 Hyundai Elantra?

11. Disconnect the battery cables (negative first, then postive). 2. Use a screwdriver to pry out [very gently and carefully] the gear selector trim bezel from console. 3. Remove the screws holding the console to the floor. 4. Lift the console up and over the shift lever. Disconnect antenna electrical connectors and remove the console from vehicle.


How do you remove the console in a 2001 altima?

In order to remove the console in a 2001 Altima, you have to remove the various screws holding it in place. There are screws on each side and on the outside at an angle with the AC knobs. You will also need to flip the shifter bezel out with a flat?æhead screwdriver to find the rest of the screws.?æ


How do you change the cigarette lighter in a Mazda miata?

The cigarette lighter is locked into the radio console bezel that surrounds the radio, HVAC controls, etc. The bezel is not very easy to remove. First you must unscrew the shifter knob. Then remove the center console - two screws in the armrest console, then you must pry up the power window switch with a very thin putty knife, unplug and remove it, and then remove the screw beneath it. Then the center console will lift up and out of the way, exposing two screws at the bottom of the bezel surrounding the radio and containing the cigarette lighter. Remove those two, and then the bezel can be carefully pried loose from the dash - It is held in by metal tangs.Once this bezel is loose from the dash panel, you can unplug the airbag switch and cigarette lighter lead, and it's free.The lighter itself is held in place by an orange collar surrounding the metal body of the lighter - it is a one-way installation with little plastic fangs that press through the bezel and lock the orange fitting into place. Attempt to remove this at your own risk, you risk breaking the bezel. I opted to snap off the one-way fangs that hold it into the bezel from the rear and replace it, it's part of the factory part you get from the Mazda dealer anyway. Assembly is the reverse of disassembly, etc.This is a fiddly non-trivial project.


Do you have to remove the entire console base that stretches from the arm rest up to the dash when cleaning the console on a 1993 Mustang?

Yes, it is all one piece. Remove the rubber bumpers under the lid, remove the screws and compartment liner; remove the 2 screws under the liner; remove the shifter bezel by pulling up; remove the 2 screws that hold the front of the console to the dash; pull up on the emergency brake handle as high as you can, then pull the console back and raise the rear of console and pull up to clear the emergency brake handle.


How do you uninstall factory radio in 2000 Toyota Corolla?

RADIO REMOVAL AND IN-DASH INSTALLATION: NOTE:THE FACTORY RADIO PROVISION IS FOR A DIN ISO STEREO THATREAR-LOADS BEHIND THE TRIM BEZEL. THERE IS ALSO AN ALTERNATEDOUBLE DIN ISO RADIO LOCATION WITH A CUP HOLDER IN THE MIDDLE OF THE CONSOLE WHERE THERE IS A STORAGE POCKET. . CAREFULLY PULL OUT ON THE DASH RADIO/CLOCK DASH BEZEL TO RELEASE, UNPLUG SWITCHES, AND REMOVE THE BEZEL. 2. EXTRACT THE (4) SCREWS SECURING THE RADIO TO THE DASH, UNPLUG CONNECTORS AND ANTENNA AND REMOVE RADIO.. Hope this helps. PDE


How do you remove the stock radio on a 2003 tiburon?

push open the ashtray to give yourself room to fit a flathead screwdriver to the bottom left of the bezel, do not remove the ashtray. pry up the bottom left part of the bezel, then the bottom right, then the middle left, then the middle right, then the top left, and finally the top right . the bezel should come right off. remove the five connectors attached to the bezel by pushing down on the taps and pulling them out. next remove the four Phillips head screws at each corner of the stereo. pull out the stereo and remove the wiring harness by pushing down on the tab and just pull out the single black antenna wire.


How do you remove the console of a 1987 Olds Calais so you can ret the factory stereo out?

I have an 87 Calais automatic with a floor shifter. The console doesn't have to come out. The bezel around the radio snaps into the lower dash with 4 clips. Carefully pry out the bezel and then you'll be able to get to the mounts for the radio. I have pictures of the dash with the radio removed if it will help. E-mail kurt_wy@yahoo.com if you want to see them.