you'll have to turn the steering wheel to left if I'm not mistaken
IT 'S ON THE RADIATOR SUPPORT BEHIND THE HEADLIGHT. THERE IS A HORN ON EACH SIDE.
Exhaust Manifold Removal & Installation 4.6L, 5.4L and 6.8L Engines 1. Raise and safely support the vehicle. 2. Remove the front fender splash shield. 3. For the left-hand exhaust manifold, remove the EGR valve-to-exhaust manifold tube and disconnect the Differential Pressure Feedback Exhaust [DPFE] gas recirculation transducer hoses. 4. Remove the oil stick from the engine. 5. On the 4.6L and 5.4L engines, remove the catalytic converter-to-exhaust manifold bolts. On the 6.8L engine, remove the front exhaust pipe from the manifold. 6. Remove the exhaust manifold mounting nuts, then remove the exhaust manifold itself. 7. Remove and discard the old gasket. 8. Clean and inspect the exhaust manifold for damage. To install: 9. Position a new gasket and the exhaust manifold onto the engine block. 10. Install the mounting nuts and tighten, in the sequence shown, to 13-16 ft.lbs. [18-22 Nm] on the 4.6L and 5.4L engines. Tighten the nuts to 17-20 ft.lbs. [23-27 Nm] on the 6.8L engine. {Tighten the passenger side exhaust manifold bolts in the order shown-4.6L and 5.4L engines} Kriss x kross 11. On the 6.8L engine, tighten the exhaust manifold-to-front pipe fasteners to 27-34 ft.lbs. [34-46 Nm]. 12. On the 4.6L and 5.4L engines, attach the catalytic converter to the exhaust manifold, then install the catalytic converter-to-exhaust manifold bolts and tighten to 25-34 ft. lbs. [34-46 Nm]. 13. Install the oil stick. 14. For the left-hand exhaust manifold, install the PDFE transducer hoses if equipped, and EGR-to-exhaust manifold tube. Tighten the upper and lower fitting to 26-33 lbs. [35-45 Nm]. 15. Install the front fender splash shield. 16. Lower the vehicle to the ground.
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disconnect the negative battery cable * Drain the cooling system * Remove the cooling fan then remove the serpentine drivebelt 2.2L OHV Engine * Remove the water pump pulley from the front of the water pump * Remove the coolant reservoir hoses * Detach the water pump retaining bolts and remove the pump from the vehicle 2.3L And 2.4L OHC Engines * Disconnect the oxygen sensor harness connector * Raise the vehicle and support it securely on jackstands * Remove the exhaust manifold brace and loosen the exhaust manifold bolts * Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine * Remove the exhaust manifold pipe from the exhaust manifold * Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging * Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head * Remove the timing chain cover from the engine * Remove the timing chain tensioner * Remove the water pump cover bolts from the engine block and the timing chain housing * Remove the water pump bolts and separate the assembly from the housing
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disconnect the negative battery cable * Drain the cooling system * Remove the cooling fan then remove the serpentine drivebelt 2.2L OHV Engine * Remove the water pump pulley from the front of the water pump * Remove the coolant reservoir hoses * Detach the water pump retaining bolts and remove the pump from the vehicle 2.3L And 2.4L OHC Engines * Disconnect the oxygen sensor harness connector * Raise the vehicle and support it securely on jackstands * Remove the exhaust manifold brace and loosen the exhaust manifold bolts * Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine * Remove the exhaust manifold pipe from the exhaust manifold * Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging * Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head * Remove the timing chain cover from the engine * Remove the timing chain tensioner * Remove the water pump cover bolts from the engine block and the timing chain housing * Remove the water pump bolts and separate the assembly from the housing
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disconnect the negative battery cable * Drain the cooling system * Remove the cooling fan then remove the serpentine drivebelt 2.2L OHV Engine * Remove the water pump pulley from the front of the water pump * Remove the coolant reservoir hoses * Detach the water pump retaining bolts and remove the pump from the vehicle 2.3L And 2.4L OHC Engines * Disconnect the oxygen sensor harness connector * Raise the vehicle and support it securely on jackstands * Remove the exhaust manifold brace and loosen the exhaust manifold bolts * Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine * Remove the exhaust manifold pipe from the exhaust manifold * Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging * Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head * Remove the timing chain cover from the engine * Remove the timing chain tensioner * Remove the water pump cover bolts from the engine block and the timing chain housing * Remove the water pump bolts and separate the assembly from the housing
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disconnect the negative battery cable * Drain the cooling system * Remove the cooling fan then remove the serpentine drivebelt 2.2L OHV Engine * Remove the water pump pulley from the front of the water pump * Remove the coolant reservoir hoses * Detach the water pump retaining bolts and remove the pump from the vehicle 2.3L And 2.4L OHC Engines * Disconnect the oxygen sensor harness connector * Raise the vehicle and support it securely on jackstands * Remove the exhaust manifold brace and loosen the exhaust manifold bolts * Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine * Remove the exhaust manifold pipe from the exhaust manifold * Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging * Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head * Remove the timing chain cover from the engine * Remove the timing chain tensioner * Remove the water pump cover bolts from the engine block and the timing chain housing * Remove the water pump bolts and separate the assembly from the housing
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disconnect the negative battery cable * Drain the cooling system * Remove the cooling fan then remove the serpentine drivebelt 2.2L OHV Engine * Remove the water pump pulley from the front of the water pump * Remove the coolant reservoir hoses * Detach the water pump retaining bolts and remove the pump from the vehicle 2.3L And 2.4L OHC Engines * Disconnect the oxygen sensor harness connector * Raise the vehicle and support it securely on jackstands * Remove the exhaust manifold brace and loosen the exhaust manifold bolts * Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine * Remove the exhaust manifold pipe from the exhaust manifold * Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging * Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head * Remove the timing chain cover from the engine * Remove the timing chain tensioner * Remove the water pump cover bolts from the engine block and the timing chain housing * Remove the water pump bolts and separate the assembly from the housing
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disconnect the negative battery cable * Drain the cooling system * Remove the cooling fan then remove the serpentine drivebelt 2.2L OHV Engine * Remove the water pump pulley from the front of the water pump * Remove the coolant reservoir hoses * Detach the water pump retaining bolts and remove the pump from the vehicle 2.3L And 2.4L OHC Engines * Disconnect the oxygen sensor harness connector * Raise the vehicle and support it securely on jackstands * Remove the exhaust manifold brace and loosen the exhaust manifold bolts * Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine * Remove the exhaust manifold pipe from the exhaust manifold * Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging * Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head * Remove the timing chain cover from the engine * Remove the timing chain tensioner * Remove the water pump cover bolts from the engine block and the timing chain housing * Remove the water pump bolts and separate the assembly from the housing
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disconnect the negative battery cable * Drain the cooling system * Remove the cooling fan then remove the serpentine drivebelt 2.2L OHV Engine * Remove the water pump pulley from the front of the water pump * Remove the coolant reservoir hoses * Detach the water pump retaining bolts and remove the pump from the vehicle 2.3L And 2.4L OHC Engines * Disconnect the oxygen sensor harness connector * Raise the vehicle and support it securely on jackstands * Remove the exhaust manifold brace and loosen the exhaust manifold bolts * Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine * Remove the exhaust manifold pipe from the exhaust manifold * Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging * Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head * Remove the timing chain cover from the engine * Remove the timing chain tensioner * Remove the water pump cover bolts from the engine block and the timing chain housing * Remove the water pump bolts and separate the assembly from the housing
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disconnect the negative battery cable * Drain the cooling system * Remove the cooling fan then remove the serpentine drivebelt 2.2L OHV Engine * Remove the water pump pulley from the front of the water pump * Remove the coolant reservoir hoses * Detach the water pump retaining bolts and remove the pump from the vehicle 2.3L And 2.4L OHC Engines * Disconnect the oxygen sensor harness connector * Raise the vehicle and support it securely on jackstands * Remove the exhaust manifold brace and loosen the exhaust manifold bolts * Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine * Remove the exhaust manifold pipe from the exhaust manifold * Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging * Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head * Remove the timing chain cover from the engine * Remove the timing chain tensioner * Remove the water pump cover bolts from the engine block and the timing chain housing * Remove the water pump bolts and separate the assembly from the housing
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disconnect the negative battery cable * Drain the cooling system * Remove the cooling fan then remove the serpentine drivebelt 2.2L OHV Engine * Remove the water pump pulley from the front of the water pump * Remove the coolant reservoir hoses * Detach the water pump retaining bolts and remove the pump from the vehicle 2.3L And 2.4L OHC Engines * Disconnect the oxygen sensor harness connector * Raise the vehicle and support it securely on jackstands * Remove the exhaust manifold brace and loosen the exhaust manifold bolts * Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine * Remove the exhaust manifold pipe from the exhaust manifold * Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging * Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head * Remove the timing chain cover from the engine * Remove the timing chain tensioner * Remove the water pump cover bolts from the engine block and the timing chain housing * Remove the water pump bolts and separate the assembly from the housing
Caution:On models with a Delco Loc 2 or Theftlock audio system be sure the lockout feature is turned off before proceeding * Disconnect the negative battery cable * Drain the cooling system * Remove the cooling fan then remove the serpentine drivebelt 2.2L OHV Engine * Remove the water pump pulley from the front of the water pump * Remove the coolant reservoir hoses * Detach the water pump retaining bolts and remove the pump from the vehicle 2.3L And 2.4L OHC Engines * Disconnect the oxygen sensor harness connector * Raise the vehicle and support it securely on jackstands * Remove the exhaust manifold brace and loosen the exhaust manifold bolts * Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine * Remove the exhaust manifold pipe from the exhaust manifold * Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging * Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head * Remove the timing chain cover from the engine * Remove the timing chain tensioner * Remove the water pump cover bolts from the engine block and the timing chain housing * Remove the water pump bolts and separate the assembly from the housing