remove the passenger pad first, when removed it uncovers screws on the rear of the drivers seat. Remove these and it comes off.
The ac blower fan is removed with three screws from the under side of the dash on the passenger side.The ac blower fan is removed with three screws from the under side of the dash on the passenger side.
Remove the screws that hold the headliner in place. With the headliner removed the overhead console retaining bolts will be visible. Remove the retaining bolts. Remove the wiring harness from the console.
To remove the poor panel on Vectra the screwdriver that will be used to unscrew the screws. Once the screws have been removed, the door panel on Vectra can then be removed.
remove door panel then remove screws behind mirror. remove door panel then remove screws behind mirror.
You will need to remove the headliner. With the headliner removed you will be able to see the overhead console retaining screws. Remove the retaining screws.
Remove the instrument panel cover retaining screws. There are four screws that need to be removed. The instrument panel light bulb's will be visible. Push the light bulb in and turn at the same time to remove the light bulb.
To remove the spring loaded wiper arm you have to first of all to unscrew the screws. After the screws have been removed, the spring loaded wiper arm can then be removed.
depending on what year you have the screws are in different places for the dash but after you remove the screws just gently pull it off, the pins will release and the screws holding the stereo in place will be visible.
You need to remove the rear seat before you can removed the front. First removed the one screw on the back of the rear seat then removed the two screws on the front of the rear seat. You can not get to the front screws until you remove the rear screw.
You need to first remove the door trim. This is because one of the 3 mounting screws that hold the mirror on can only be accessed when the door panel is removed.
Removing the back seat in the Kia Rio is simple. Remove the screws or bolts from the lower cushion and remove cushion. Then remove the now visible screws and remove the remaining parts.
How do I get the front grill off my 1997 Chevy suburban? I've removed the six visible screws holding it in place, but it still won't come out..
There are two screws under the ashtray. Remove the astray to access the screws. Remove the screws. Once the screws are removed carefully pull the plastic frame covering the radio and the climate controls. Once the frame is removed you will see two or four screws depending on the model vehicle. Remove the screws and pull the radio out. Once the radio is out disconnect the connectors and the antenna. Installation is the reverse of removal.
two screws are visible when the tail gate is open. remove these screws and pull on the light distribute the pressure. the clips will let go with a little pull. remove wire harness from the light housing by counter clockwise turn.... two screws and 4 clips per light
Remove the Toyota Camry headliner. The overhead console retaining screws will be visible. Remove the retaining screws and the console will come off.
door panels can usually be removed by taking out all visible screws holding the plastic on, and then using a screwdriver or pry bar to pop out the plastic rivets.
2 screws on outside edge and 2 screws on inside(undo tailgate)
the folding tray OS bolted to the passenger seat. the passenger seat must be removed in order to unbolt the tray from the seat.Do not remove the passenger seat. remove the cover that attached to metal bracket of p. seat. it's mounted with two plastic screws. use flat screw driver to remove. then you will see 3 bolts on the bracket attached to p. seat. remove bolts and pull away.
fuel pump is under the rear passenger seat . when you remove the seat there will be a panel with four screws. remove the screws than panel to acesss fuel pump.
A 1995 Honda Odyssey factory radio stays in place with several mounting screws which are located underneath many panels which need to be removed. When the mounting screws taken off remove the head units mounting bolts which now will be visible. Slide the radio out and remove the stock wire harness.
Can someone tell me how to remove a taillight (after screws removed) from a 1991 Chevy s-10 a.s.a.p. once you have the screws removed the tail light housing should wiggle out, gently.
There are 10 screws in the grille that have to be removed. Remove all of them and then you should have the grille out. Simple as can be.
To remove the tail light cover you need to open the tailgate and locate the two hex screws that hold the light in place. Once these are removed gently pull the light cover toward the rear of the vehicle.
In order to remove a house door handle, you will need to take a screwdriver and remove the screws from the exterior of the door. Once the screws are removed, the handle should simply pop out.