Jeep Liberty
Ford Expedition Eddie Bauer
Ford Expedition XLT
Chevy Colorado

How do you remove the passenger side rear panel on a 2005 Liberty to install trailer wiring?

454647

Top Answer
User Avatar
Wiki User
2011-09-12 20:32:54
2011-09-12 20:32:54

I don't think that is neccasary. If you remove the plug from the tailight and feed it down the bumper it gives you plenty of work room below the bumper.

DEALER ANSWER BELOW

Step 1. Pop off the center plastic piece the rules the lenghts of the door. Step 2. Remove the cargo stap hook that is about halfway up the trim panel. (take a Phillips screw driver and turn it 90 degrees and pop the thing out. Step 3. Pull on the bottom corner of the panel until it starts to pop and work your way up so you can gain access to the back. Step 4. pull back the red tab on the light harness to release them. Step 5. Connect you harnesses and feed the end through the thru body gromet. (you have to make a slit in the gromet to pass the plug through. Step 6. Apply silicon around the wiring at the gromet to seal it up. Step 7. Feed your wiring down and to your hitch staying away from your exhaust. Use some zipties if you have em. Step 8. Let your silicon dry for for a little while until it has set up. Don't wait 24 hours or anything. Step 9. Reinstall your back panel, cargo strap point, and center trim.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Remove the inside door panel of your 1993 Chevrolet Lumina. Remove the passenger mirror wiring harness. Remove the passenger mirror retaining bolts. Reverse the process to install the new passenger mirror.

User Avatar

Should be a bolt in each corner of the seat

User Avatar

remove door panel then remove screws behind mirror. remove door panel then remove screws behind mirror.

User Avatar

Chevrolet Lumina. Remove the wiring harness or the mirror linkage. Remove the mirror retaining bolts. Reverse the process to install the new passenger side mirror.

User Avatar

Begin by removing the inside passenger door panel. Remove the wiring harness from your passenger side electric mirror. Remove the mirror retaining bolts. Reverse the process to install your new electric passenger side mirror.

User Avatar

How do I install passenger side mirror 2010 Ford Explorer

User Avatar

The passenger window on a windstar is best installed by a professional. However, if you have some auto repair experience, you can easily remove the door panel on the door by removing the screws and then you will be able to install the new window.

User Avatar

On driver side, you will have to remove the steering assembly. With the passenger side you should only have to remove the factory manifold.

User Avatar

under passenger seat in right rear. loose nut from front side to remove.

User Avatar

Begin by removing the 1994 Chevy passenger side door panel. Remove the window motor wiring harness. Remove the window motor linkage. Remove the window motor retaining bolts. Reverse the process to install the new window motor.

User Avatar

remove from in side pushing out with pry bars and an smallrope pasents jental

User Avatar

I have a 2004 and I haven't tackled that one yet but I know of some guys that remove and install race seats and all. These guys can help you. I

User Avatar

You have to remove the passenger fender well to get to it. After you remove it, unbolt it and unplug it and it's out. VERY simple to replace, NOT so easy to get to though.

User Avatar

Disconnect battery, jack up passenger side of car in the front, look under the engine on passenger side, remove the bolts, disconnect the wiring and remove. Install in the reverse order.

User Avatar

To install the tubular side step on the Jeep Liberty, first remove the bolts and the running boards if the vehicle has them. Then, install the side step with the mounting brackets included. You might need to drill into the frame of the vehicle to place the bolts for the brackets. Then, add the step which bolts to the mounting bracket.

User Avatar

Loosen and remove the nuts on the back of the bumper. Remove the bolts from the bumper. The bumper will come off. Reverse the process to install the new front bumper.

User Avatar

Yes you can. If you look on top of your vehicle, the passenger side and driver side shoulder have two rectangular slot each where you remove and install the roof rack.

User Avatar

On the bottom of the dash on the passenger side remove the black cover then remove the bolts on the blower and disconnect the wire. Reverse above to install.

User Avatar

remove inside pannel you will see 3 nuts behind mirror remove and mirror will come out install new

User Avatar

Follow the instructions on how to install the trailer hitch from H and A. Here is the link http://www.handa-accessories.com/element/elementhitch.pdf

User Avatar

Remove the wiring harness from the 2003 Jeep Liberty pressure switch. Remove the power steering pressure switch retaining screws. Reverse the process to install the new power steering pressure switch.

User Avatar

You will need to remove the front tire and wheels from your 2002 Jeep liberty. Remove the brake pads and break assembly. Tap the rotors with a hammer or mallet. The rotors will come off. Reverse the process to install the new rotors.

User Avatar

My husband just did ours, it was I think only 3 screws on alternator. Once you remove the screws, you have to rock the alternator left and right to remove (like a lever). It looked very simple.

User Avatar

remove passenger seat in 2003 cadillac cts

User Avatar

On a light trailer or small boat trailer you remove the bearing cap, pack it with grease and re-fit it.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.