answersLogoWhite

0


Top Answer
User Avatar
Wiki User
Answered 2015-07-15 20:05:23

Take a punch and push the pin through as far as you can, then twist it out with a pair of pliers

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

How important are vacuum hoses 1991 Chevy beretta?

The vacuum hoses are very important in a 1991 Beretta. Without the vacuum lines, the engine will not run properly, and the power brakes will not function.


How do you remove the heater core and hoses from 1996 Chevy sub 5.7 k1500?

how do you remove the heater core and hoses from 1996 Chevy sub 5.7 K1500


How do you replace a radiator in a 1992 Chevy S10 pickup 4-cylinder 5 speed no ac?

Remove fan shroud Drain radiator Remove upper and lower radiator hoses Remove upper mounting bolts Lift radiator out of lower support cradle


How do you remove the heater hoses on a 2003 Chevy truck?

you need the special tool its about 30 bucks from snap on


How do you remove the heater core in a 1988 Chevy G20?

Drain the water from your 1988 Chevy cooling system. Remove the heater core water supply hoses. Remove the heater core retaining bolts. The heater core will come out.


How do you take out the radiator in a 1994 Chevy Corsica?

I had to take the bolts off of the fan. Remove the plastic fan cover. Diconnect 2 hoses underneath. Watch for oil. disconnet hoses on top. Unbolt radiator and remove. Make sure all hoses fit on new radiator. I have to remove twice since i didnot check


Where is ecm hoses on 2006 Hyundai sonita 4-cylinder?

There are no ECM hoses. The ECM is the Electronic Control Module.


Heater core removal from 1972 Chevy Nova?

Drain the water from your 1972 Chevy Nova cooling system. Remove the heater core water supply hoses. Remove the heater core retaining bolts.


97 Chevy Malibu 4 cylinder replace water pump?

The water pump on a 97 Chevy Malibu 4 cylinder is replaced by removing the engine accessories, drive belt, and radiator hoses. The pump can then be unbolted, removed, and a new pump installed.


Where are the vacuum hoses on a 2000 Chevy Cavalier?

There are several vacuum hoses routed throughout a 2000 Chevy Cavalier. To find the hoses, use a factory service repair manual of a 2000 Chevy Cavalier.


How do you remove cylinder head on a astra 1.7cdti?

To remove the cylinder head on an Astra 1.7 CDTI, disconnect the battery cable and remove the lower engine cover. Drain the cooling system and remove the oil filter. Remove the air filter hoses and disconnect the crank case breather hose from the valve cover.


What could cause a 1994 Chevy Beretta to over heat?

You should check your thermostat and maybe your water pump,catalitc converter, heater core, hoses might have holes in them or maybe low and colant


How do you replace the AC compressor on a 1997 Chevy Malibu?

Remove the air conditioning hoses from your 1997 Chevy Malibu air conditioning compressor. Remove the compressor belt. Remove the compressor retaining bolts. Reverse the process to install your new air conditioning compressor.


How do you install a heater core in a 1998 Chevy Camaro?

Remove the water from your 1998 Chevy Camaro cooling system. Remove the water supply hoses from the heater core. Remove the heater core retaining bolts. Reverse the process to install the new heater core.


How do you remove power steering pump from a 91 olds ceria 4-cylinder?

The power steering pump is held on by several bolts and hoses and the power steering belt. Loosen one of the bolts on the pump to adjust it down so you can remove the tension from the belt. Once that is done, start removing the hoses carefully. They will be leaking fluid so it's good to place a rag underneath. Once the hoses are disconnected, remove the bolts holding the pump in place and it will be free.


What is procedure for installing a new distributor shaft in a 1974 Chevy 350 motor with electronic ignition?

remove dist.cap.unplug wires and hoses mark rotor where it is pointing...remove holddown bolt remove dist.


What colour are hoses for an acetylene cylinder?

red


How do you remove the heater core from a 1989 Chevy G20 van 305 engine with AC?

Begin by removing the water supply hoses from your 1989 Chevy heater core. Remove the heater core retaining bolts. The heater core can be removed.


How do you remove a heater core from a 1987 Chevy Blazer S10 2.8?

Locate the heater hoses in the engine compartment, follow them back to the fire wall, unhook both hoses at the firewall. The core is on the inside of the cab right behind where you unhooked the hoses. You will have to remove most of the lower dash board and the heater air box to access it. Not a very hard job, just a lot of BS to remove to get to it.


How do you remove heads on a 305 Chevy?

To remove the heads on a 305 Chevy, first disconnect the battery, carb and throttle cables. Also disconnect the sensors and vacuum hoses. Unplug water temp gauge sensor on the thermostat and disconnect pump from brackets.


How do you change a heater core in a 1993 corvette?

Remove the water supply hoses from your 1993 Chevy Corvette heater core. Some water will drain out of the hoses and the heater core. Remove the heater core retaining bolts. Reverse the process to install the new heater core.


Chevy Venture heater hoses?

Chevy Ventures have two heater hoses. One is located on the intake connection and the other located on the output connection.


How do you replace a power steering pump on a 1969 Chevy 327 engine?

Remove the belt from your 1969 Chevy power steering pump. Remove the power steering pump hoses. Remove the power steering pump retaining bolts. Reverse the process to install your new power steering pump.


Replace the heater core on a 1985 Chevy van G30?

Remove the water supply hoses from your 1985 Chevy heater core. Remove the heater core retaining bolts. The heater core will come out. Reverse the process to install your new heater core.


How do you change the fuel filter on a 1990 Ford Tempo?

The primary fuel filter on a 1990 Ford tempo is located on the passenger side of the engine compartment. It is a cylinder about 3 inches long and 3 inches in diameter, to remove it you will have to remove 2 screws that were placed into the strut tower adn remove the hoses attached (htere may be pressure in the lines as it is a pressurized fuel system) to remove the hoses you must remove the white clips that hold the hoses in place by carefully spreading the clips over the retainer (must be replaced if broken) the hoses will just slip off