• Power Steering
  • Ford Thunderbird
  • Chevy Suburban
  • 1995-2005 Chevy Cavaliers

How do you remove the power steering pully on a 1990 Ford Thunderbird 3.8L?

User Avatar

Wiki User

βˆ™ 2015-07-15 20:55:51

Best Answer

You have to have a puller that fits on the groove just behind the front edge of the pulley.

2015-07-15 20:55:51
This answer is:
User Avatar

Your Answer


Related Questions

How do you reinstall the power steering pump pully on a 1995 Chevy silverado 350 v8?

How do you remove power steering pulley on a 1990 ck truck

1996 dodge ram 5.9 power steering pully removal?

1996 dodge ram 5.9 power steering pully removal?

How do you install power steering pully Chevy Tahoe?

Most power steering pulleys require a special tool to remove and replace. Many auto parts stores will rent you the proper tools to do the job.

How do you remove powersteering pully on a 1994 s-10 zr2 pickup with 4.3 vortec?

You will need a power steering pulley puller. It is designed to remove and install the power steering pulley. If you attempt to remove the pulley without it you will probably damage the pulley or the pump or both.

How do you pull off the pulley on a power steering pump on a 1993 f 150?

To the best of my knowledge on this truck you have to first remove the power steering pump then get a tool called a "power steering pully puller" and make sure you get one with the power steering pully installer with it. Your local auto parts store will have one and a few have ones they will loan you. The parts representative there should be able to instruct you on the proper use of both tools.

Can you bypass power streering pully on 1999 Plymouth voyager?

No, if you do you will have no power steering. You could not steer this vehicle with the power steering pump bypassed.

What type of energy involved in power steering pump?

The majority of power steering pumps work off hydrolic power. There is a belt that runs from a pully on the front of the pump to a drive pully on the front of the engine (usually attached to the crank shaft). This pully turns the pump and generates the hydrolic pressure.

When replacing Saturn SL1 alternator does power steering pump need to be removed to get access to bolts?

No you dont need to remove the power steering pump to get at the bolts. if you go directly down from the very bottom of the pully on the power steering pump the bolt holding the top of the alternator should be right there. all you have to do is remove it and the alternator should come out.

How do you remove the pully on the power stearing pump on a 97 suburban?

That requires a special puller. It's called a power steering pulley PULLER. You can rent them at Advance Auto parts stores.

How do you replace power steering pump pully?

With a power steering pump pulley puller. Many auto parts stores will rent you the proper puller to do the job.

How do you remove the pulley from a 1991 6 cylinder Jeep Cherokee power steering pump?

The belt pully on most Cherokees is pressed onto the pump shaft. It will take the appropriate size gear puller to remove. The same remains on installing the pully on a new pump. The action of the puller has to be reversed and used to press the pully onto the new shaft.

How do you replace a serpentine belt on a 1992 Oldsmobile Delta 88?

Locate the idler spring tension pully below the power steering pump. The pully is pressing down on the belt and has to be pulled away from the belt so you can remove belt from the power steering or alternator pully. You need a socket that fits the bolt on the tension pully and a socket wrench with a 2 to 3 foot pipe extension. Attach to bolt head, apply counter clockwise pressure enought to loosen belt to allow enough slack to remove belt. Do not get your fingers between the belt and any pully when removing. You might not like it. To reinstall. Route the belt and release the tension again enough to put the belt back on the last pully.

Where is the power steering pump on a 1988 Cadillac Deville?

top pully, nearest to the front of the vehicle.

What does it mean if the steering wheel on your car squeals when you turn it?

tighten the belt or replace it Maybe a loose power steering box or a worpted pully.

How do you remove steering wheel on 1995 suburban?

you need to buy a steering wheel. {Cheap at auto part store} remove your horn cover screws from behind the steering wheel. attach the pully, screw it in and it will pull the wheel off.

Removing pully from power steering pump do you need to remove the pump or is there a trick to it?

To get the pulley off requires a pulley puller to do it. You do not have to remove the PS pump to do it. It also takes a special tool to put the pulley back on too.

When replacing the water pump on a 98 Bonneville how do you reach the bolt that is behind the power steering pully?

You may have to remove the P/S pump or some pulleys have a hole in then to access the bolt

What pully do you run the power steering belt to on a 1983 350 Chevy Silverado truck?

crank pulley.

How do you replace a power steering pump on a 1998 Chevy Cheyenne PU 5.7 L 350 engine The pump has a pressure switch - how is it removed?

buy or rent a power steering pully puller tool. Remove the serp belt, pull off the pully, unbolt the pump from its bracket, unscrew the pressure line, remove clamp the remove the return hose use the new oring or plastic washer to seal the new pump to the hose The senser just unscrews be careful of its weak plastic

1994 bad water pump Manual says remove pulley from power steering pump to get at bracket Pully remover rented won't budge it loose It wiggles in and out about 18 Is that normal Suggestions?

Did you remove the nut from the pulley first?

How do you remove the power steering pump on a 1998 GMC Sierra 1500?

carefully with a special pully tool you can rent at most part stores. you have to remove the pulley to acess 3 bolts that hold the pump in place. I did it on a 95 1500

How do you keep the power steering pump pulley from turning when you try to loosen the bolt holding it to the pump on a 97 Suburban?

I a 97 pick up and the power steering pully is pressed on and pressed off

Where is the idler pully on a 1999 Jeep Wrangler?

front drivers side of the engine next to the power steering pump

How do you put the pully on a power steering pump on a 1995 chev pickup?

You can rent the proper tool to that job from your local auto parts store. The tool can remove and install the pulley with out damaging pump and/or pulley.

How do you remove the power steering pully on 1999 350 suburban with 4wd Is the Allen head bolt a right or left hand thread?

The Allen head is NOT a bolt. Go to an Auto parts store and get a Power Steering Pulley Remover tool. The pulley is pressed on, there will be instructions with the tool or ask the counter person.