0
How do you remove the power window motor and regulator from a 1993 Mazda MPV?
Wiki User
∙ 14y ago
Remove the door panel. Remove the plastic door seal carefully. Keep it to reinstall. Remove the speaker outside metal panel, 4 bolts. The speaker needs to be unplugged, 2 pin connector.
Unplug the regulator connector on the bottom left door hole. There are some white regulator hose clamps that can be pinched and removed.
There are 2 screws in the motors "L" bracket that hold the glass in. I could get to them through the holes in the door. I had a helper hold the glass.
There are 4 bolts to remove on the bottom center of the door that hold the motor. There are 2 nuts directly up from it that hold the metal rail in place. Remove these, then swing the motor up and out of the hole left from removing the speaker bracket. Your new window regulator should come with new hose clamps. I compared the locations to the old one and moved them so it would match the hole locations. Mine were off quite a bit.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How to Replace window motor in a 1999 suburban?
How to remove the window motor from the regulator
How do you remove and replace Window motor regulator on a 2000 intrigue?
remove your door panel there will be three screws holding it on. then you have to remove the screws holding your window to the regulator. then unbolt regulator and motor from door. Undo wiring going to motor.
How do you replace achieva power window motor?
Remove the window regulator assembly from the door.Remove the motor from the regulator by drilling out the attaching rivets with a 3/16 in. drill bit.Connect the window motor to the regulator with 3/16 in. rivets.Install the window regulator assembly.
If removeing window motor on firebird do you have to remove window and regulator?
Depending on the year, 92 through 97. Yes! The motor is riveted to the regulator. You must remove as a unit, drill a hole in regulator arm and insert a bolt and nut to keep from springing back. Then drill out rivets to motor replace motor with bolts and remove bolt in regulator arm.
How do you change the power window motor on a 1994 Pontiac Grand Prix?
Remove the window regulator and motor from the door as an assembly. Drill out rivets that hold motor to regulator and replace motor. Regulator needs to be riveted back into door for reassembly
Would the window motor and regulator from a 95 Probe work on a Mazda MX-6 LS of the same year?
no
How do you replace 1995 Toyota Celica power window regulator?
remove back seat, remove screws bottom and top of panel, remove panel. remove 3 bolts and motor arm, window and regulator will pull out.
How to raise the driver side window to have room to remove the power window motor in a 2000 Mazda MPV when the motor is seized.?
Completely remove the inside door panel. Since the window is down, the two screws that hold the window glass to the regulator should be easily acessable. Remove these two screws. Disconnect the regulator from the window glass. Push the window glass up to the very top. A bungy cord can be used to hold the glass up while the motor is being removed. Hook the bungy cord to the top of the door. Hook the other end to the bottom of the window glass.
How do you replace window regulator 1991 3000gt?
Take the door panel off,you will need to remove 3 bolts for the window motor and then 3bolts(maybe4) that hold the regulator to the window
How do you replace 3000 gt door window regulator?
First, lower window approximately half way. This allows you access to the bolts that attach window to the regulator. Remove door panel. Using a 10mm wrench, remove the two bolts that hold window to the regulator. Then there are two upper and two lower bolts holding the regulator to the door. Then you remove the three bolts for the window motor which is toward the front of the door. You have to also disconnect the plug for the windo motor to remove the entire window regulator and motr that are all one unit. Replace the unit in the reverse way.
How do you replace window motor 1996 Chevy Astro?
1. Remove the power window regulator2. Install a pan head sheet metal tapping screw through the sector gear and the backing plate at the hole provided to lock the sector gear into position. Then drill out the motor to regulator attaching rivets.3. Remove the motor from the regulator.To install:1. Lubricate the motor drive gear and the regulator sector teeth. Install the motor to the regulator and check the mesh of the motor to the regulator.2. Install rivets to the motor and the regulator.3. Remove the sheet metal tapping screw.4. Install the power window regulator.
How do i change the right rear window motor on a 2002 deville?
It is best to replace entire regulator as one unit. Remove door panel. Remove bottom nut of regulator, and remove two top nuts of regulator. Loosen two bolts on bracket holding window. Support window, and carefully remove regulator as one unit.
