CV Joints
Nissan Maxima
Nissan Sentra

How do you replace CV joints on a Nissan Stanza?

535455

Top Answer
User Avatar
Wiki User
2015-07-15 20:57:01
2015-07-15 20:57:01

Check your local library for a repair manual, or automedia.com

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

How do you replace the CV joints on a 1993 Nissan Sentra XE?"

User Avatar

you cannot just change the boot you will have to replace the whole axle

User Avatar

The average cost to replace CV joints is approximately $300. It is more inexpensive and less time consuming to replace both CV joints.

User Avatar

Bad CV joints. Replace the CV joints.

User Avatar

It is not cost-effective to attempt to replace just the CV joints. Rebuilt CV shafts are available for as little as $60.

User Avatar

i have a 2008 Nissan altima and my cv joints are going bad already is this right

User Avatar

1 - simplest and cheapest method- replace the axle 2- replace the CV joints and boots 3- lots of unnecessary work, very expensive - check the joints and replace as needed, replace boots

User Avatar

This should answer your question? I used it to help me replace mine on my altima. forums.nicoclub.com/zerothread/157923

User Avatar

On the Chrysler there are no such things as "CV joints". There are however "U joints". To remove them you would have to drop the driveshaft and have them pressed out by a machine shop.

User Avatar

That depends which model it is. On older models CV-joints were moulded into the driveshaft. To be replaced they had to be removed using a press and then warmed to be able to replace them. On these models it is often better to replace the whole driveshaft. On newer models CV-joints are attached with clips and can be replaced more easily.

User Avatar

The 2000 Ram had u joints, not cv joints at the front axle.

User Avatar

Maybe it is one of the other cv-joints. Each half shaft has two cv-joints. Better off replacing the complete halfshaft with a rebuilt unit than to replace the one cv-joint only.

User Avatar

The CV joints in 1999 Malibu can be replaced by removing the front tires and moving the brake lines out of the way. Next, you will need to remove the nuts for the CV joints by using force to remove it from its housing.

User Avatar

If the CV joints are in good shape, only replace the boots. A aftermarket boot can be installed with out changing CV joints. VW bugs has been doing this for years. If the joints are scored then pull the outside wheel,hub and bearing (need puller). Disconnect turning rods. Reassemble

User Avatar

the cv joints tap off with hammer,from 2005,advise changing rounded split clip when fitting new cv

User Avatar

It does have CV joints but, it is best to just swap out the complete axle assembly than to replace only the CV joint. You will spend much time and almost as much money trying to replace the CV joint than to just purchase a reconditioned axle assembly and swap it.

User Avatar

When the CV joints start to leak grease or make snapping and cracking noises.

User Avatar

It is best to replace the whole axle, Its easy to do not to mention pretty inexpensive....

User Avatar

The CV joints on a 1995 Ford Taurus can be replaced by removing the front tires, and the nuts on the lower ball joint. Next, the lower ball joint will need to be removed and the CV joint can be removed.

User Avatar

A chevy 3500 truck is not front wheel drive, so it does not have CV joints.

User Avatar

most shops will want to replace entire axle shaft which is the way to go, depending on where you take it should cost 175-250 per axle,

User Avatar

No the axle shafts use CV joints.No the axle shafts use CV joints.

User Avatar

Yes you have two drive axles that use 2 CV joints, both have an inner CV joint and an Outer CV joint

User Avatar

It is generally not cost-effective to replace individual CV joints. Rebuilt or new CV shaft assemblies in most cases cost less than the joint itself, and are a lot less work to install.

User Avatar

You would want to purchase complete axle haftshafts, not just the CV joints. It would be more time consuming and costly to just replace the CV joints. A complete rebuilt haftshaft should cost under $100 each plus labor to R&R.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.