Auto Parts and Repairs

How do you replace a front wheel hub bearing on a 95 Chevy S10 2WD 4 cylinder?

353637

Top Answer
User Avatar
Wiki User
2015-07-15 21:12:41
2015-07-15 21:12:41

on a 2wd you take off the tire then theres a cap in the middle of the rotor take it off take the pin out its a cotter pin take the nut off then carefully take the rotor off one set of bearings should come off with the rotor after you get the rotor off the other bearings will be exposed grease them or replace then the reverse the procedure

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Remove the tire and wheel from your 2001 Chevy Impala. Remove the end of the axle. Remove the wheel bearing nut. Remove the wheel bearing seal and the wheel bearing. Reverse the process to install the new front wheel bearing.

User Avatar

Here is a link to some good instructions. http://reviews.ebay.com/ebaymotors/Chevy-Silverado-4x4-Front-Wheel-Hub-Bearing-Replacement_W0QQugidZ10000000002536494

User Avatar

how to replace front wheel bearing on 1996 Hyundai elentra

User Avatar

Depending an where you live and which shop you have do the work about $300.00

User Avatar

Remove the tire and wheel from your 1997 Chevy Astro. Remove the axle end. Remove the wheel bearing nut. Remove the wheel bearing and the wheel seal. Reverse the process to install the new front wheel bearing.

User Avatar

You can replace the front bearing on 2003 Citroen Relay using air tools.

User Avatar

It's a sealed unit with the hub. You have to replace the whole hub assembly.

User Avatar

36mm. You will also need an 18 mm box wrench to replace the bearing assembly.

User Avatar

You will need to remove the tire and wheel. Remove the axle end cap. Remove the wheel bearing seal. Remove the wheel bearing. Reverse the process to install the new will bearing.

User Avatar

You can replace the front wheel bearing, on your Kawasaki Mule 3010, by removing the axle. With the axle Remove the wheel bearing will slide off.

User Avatar

Remove the tire and wheel from your Chevy Lumina. Remove the end of the axle. Remove the wheel bearing nut. Remove the wheel bearing seal and the wheel bearing. Reverse the process to install the new front wheel bearing.

User Avatar

Make darn sure it isn't the tire first. Take the strut off, and have the bearing pressed.

User Avatar

you can replace it by taking it to the shop and they will do it for you.

User Avatar

Get a Haynes repair manual. These vehicles are too complex to treat like old school vehicles.

User Avatar

To replace the front wheel bearing on a Ford Fiesta, you will need to remove the wheel. Then with a hammer you can pull the old bearing out.

User Avatar

the bearing assy comes as a complete package with the hub and ABS sensor, etc. --- 3 bolts connecting it to the knuckle (front) or arm (rear)

User Avatar

To replace the front bearing,jack up front and remove the wheel.Remove the brake caliber assembly and pads.The brake caliber guide ,held in place by 2 bolts that is bolted to the hub assembly has to be removed in order to remove the rotor.Remove the 3 bolts which hold the wheel bearing to the hub assembly,from the backside.Remove the 35mm axle nut using an inpact drill or strong arm.Tap the axle out of the assembly and the bearing assembly should come out from the front.

User Avatar

#1 cylinder is on the left of the engine as you are facing it from the front.

User Avatar

The cylinder on the very front of the engine is #1.

User Avatar

Is the wheel bearing on the front or the rear ????.. There is a big difference ...

User Avatar

If its a 4 cylinder its the very front toward radiator, if its a v6 its the very front cylinder on the drivers side


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.