0
2.2L engine
Caution Relieve the fuel system pressure before servicing fuel system components in order to reduce the risk of fire and personal injury.
After relieving the system pressure, a small amount of fuel may be released when servicing the fuel lines or connections. In order to reduce the chance of personal injury, cover the regulator and the fuel line fittings with a shop towel before disconnecting. This will catch any fuel that may leak out. Place the towel in an approved container when the disconnection is complete.
Disconnect the negative battery cable.
Caution Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.
Remove the air cleaner outlet resonator mounting screw.
Disconnect the air cleaner outlet resonator clamp at the throttle body.
Remove the air cleaner outlet duct from air cleaner outlet resonator and air cleaner assembly.
Disconnect the crankcase vent hose clamp and the crankcase vent hose from the top of the engine.
Remove the air cleaner outlet resonator.
Remove the fuel rail bracket.
Remove the fuel injector electrical connectors by pushing in the wire connector clip and pulling the electrical connector away from the fuel injector.
Remove the fuel feed inlet pipe quick connect.
Remove the fuel return pipe from the fuel pressure regulator.
Remove the fuel rail attaching bolts.
Remove the fuel rail assembly from the cylinder head.
Remove the fuel injector retaining clip.
Remove the fuel injector.
Important Visually inspect the fuel injector to see if the upper O-ring was also removed, if not, remove the O-ring from the fuel rail assembly.
2.4L engine
Caution Relieve the fuel system pressure before servicing fuel system components in order to reduce the risk of fire and personal injury.
After relieving the system pressure, a small amount of fuel may be released when servicing the fuel lines or connections. In order to reduce the chance of personal injury, cover the regulator and the fuel line fittings with a shop towel before disconnecting. This will catch any fuel that may leak out. Place the towel in an approved container when the disconnection is complete.
Disconnect the negative battery cable.
Caution Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.
Remove the air cleaner outlet resonator mounting screw.
Disconnect the air cleaner outlet resonator clamp at the throttle body.
Remove the air cleaner outlet duct from air cleaner outlet resonator and air cleaner assembly.
Disconnect the crankcase vent hose clamp and the crankcase vent hose from the top of the engine.
Remove the air cleaner outlet resonator.
Remove the vacuum hose at the fuel pressure regulator.
Remove the Camshaft Position sensor electrical connector.
Remove the fuel injector electrical connector retaining clips.
Remove the injector electrical connectors.
Remove the fuel inlet pipe at the fuel rail. (Use a backup wrench on the fuel rail inlet fitting to prevent it from turning).
Remove the fuel pipe retainer clip nut (if so equipped).
Remove the fuel pipe retainer clip bolt.
Remove the fuel rail attaching bolts.
Lift the fuel rail assembly from the cylinder head.
Loosen the fuel return pipe retaining bracket attaching screw. (Rotate the retaining bracket to allow fuel pipe to be removed.)
Remove the fuel return pipe (2) from the fuel pressure regulator.
Remove the inlet and the return pipe assemblies. Discard O-ring.
Remove the fuel rail assembly.
Alexandrine Jones
Add your answer:
Earn +20 pts
How many fuel injector does a 2000 Chevy cavalier have?
how many fuel injectors are in a Chevy cavalier
How do you replace a fuel injector on a 2001 Mazda mpv?
How do you replace a fuel injector on a 2001 Mazda mp
How do you replace a fuel injector on a 1992 Chevy Cavalier?
remove two torx screws that hold down the bracket which hold down the injectors. then you can pry out the injector whit an screwdriver but becareful not to damage the injector or o-rings
How do you replace the fuel injector on a throttle body Nissan 3.0?
how to replace fuel injector throttle body in a 1988 nissan pathfinder 3.
How fix Fuel injector leak Plymouth Voyager?
replace the rubber o rings u may have to replace the injector if its leaking fuel through it
How do you replace fuel injector on a 1999 Mazda 626 v6?
Where is the fuel injector located on a 1999 mazda 626v6
How do you replace a fuel injector on a 1999 jimmy?
if you are not mechanical, replacing a fuel injector is a specialist job requiring special tools
How often should you add fuel injection cleaner to you 2002 Chevy Cavalier?
Modern fuels have a fuel injector injector cleaner built into them. However I do recommend you use a good fuel injector cleaner such as Seafoam or Chevron Techron once a year.
How to remove and replace Mazda b3000 fuel injectors?
how do u replace fuel injector on 2001 b3000
How can you fix your fuel injector on your 1998 Chevrolet Blazer 4.3 v6?
A fuel injector on the vehicle is not serviceable, replace it with a new one.
How do you install fuel injectors in a 1993 Geo Prizm?
Remove pressure from the fuel system. Remove fuel lines and the rails. Get a fuel injector puller to avoid the risk of damaging the injector. Remove the old injector and replace it.
How do you Replace fuel injector on 2000 ford windstar 3.8?
where is the #5 injector? how long does it take to fix
